Call 01582 935272

Tracing a leak

How to find where a roof leak is coming from

A drip on the ceiling marks where water ended up, not where it got in. This guide shows how to trace it back: through the loft, by measurement, from the garden, and by testing one area at a time.

10 minute read

Get a written quote

Call 01582 935272WhatsApp us

Wind-torn membrane peeled back from a wet flat garage roof
PicturedWind-torn membrane peeled back from a wet flat garage roof.
A roof drawing with its parts named: ridge tiles, tiles, battens, underlay, raftersRidge tilesTilesBattensUnderlayRafters

Water travels before it drips

A roof leak and the stain it leaves are two different places. Rain that gets past the covering lands on the underlay, runs down it, and follows whatever lies along the way: a batten, a rafter, a pipe, the joint between two sheets. It drips only where the line runs out, and that spot can sit well down the slope from the hole, or sideways along a timber into another room.

That is why patching the tile above a stain does not always stop it. The entry point is higher than the stain, because water runs downhill, and it can be anywhere along the path the water took. Finding it means working back up that path rather than looking straight above the mark.

  • the stain shows where the water ended up
  • the path runs along timber and underlay, downhill
  • the entry point sits upslope of the stain
  • more than one entry point can feed one stain

A careful search follows a set order of its own: the ceiling, the loft, the ground, the likely junctions, and then a test. The wider roof repairs hub explains what happens once the fault is found, and the repair itself is a separate step from the search.

Read the ceiling and walls first

Start indoors, in daylight, and look at the shape of the damage as well as its position. The shape says something about the source, though it never settles it alone, so treat each row below as a lead to check and not as a finding.

Marks indoors and where they may lead
Mark seenPossible sourceNext check
Ring stain that grows after rainA fault in the covering aboveThe loft, upslope of the stain
Damp patch on the chimney breastChimney flashing or the stack itselfBoth sides of the stack outside
Damp along the top of an outer wallGutter, fascia or the eaves lineGutters and eaves in rain
Wet patch whatever the weatherPlumbing, or condensationPipes and loft ventilation

Note the date, the weather and the wind direction each time the mark changes. A mark that grows only when the rain comes from one side points to a face of the house, and a mark that grows on dry cold mornings points away from the roof covering altogether. That single observation can save a morning of searching.

Photograph the mark with a coin set next to it for scale. A second photo a week later shows whether it has grown. The Financial Ombudsman Service says it will "usually look at expert reports and photos", so the pictures help an insurer's view of a claim as well as a roofer's view of the roof.

Follow the trail through the loft

The loft is a particularly useful place to look, because the underside of the roof is visible there and water leaves marks on the way down. Go up with a torch, in daylight, and put weight on joists or firmly fixed boards only. Never put weight on the ceiling board between the joists, which will not hold a person.

Look first at the timber under the stain and move upslope. Dark trails on rafters and battens, wet insulation, a damp section of underlay, a rusted nail point or a shaft of daylight all mark the route. Water collects at the bottom of a trail and the damp reaches further than the leak, so trace the dampest and darkest timber back up to where the trail ends.

Measure from a fixed point you can find outside, such as the chimney stack, a party wall or the ridge end. Write down how far along and how far up the slope the fault lies. Outside, that measurement gives a spot to examine from the garden, and it avoids guessing from the pattern of tiles.

A pencil or chalk mark on the wet timber helps. It shows later whether the wet area has moved. If the underlay has torn, loose or sagged near the mark, photograph it, because that is the layer that should have caught the water.

  • chalk the edge of any wet timber
  • measure from the stack, the party wall or the ridge end
  • photograph tears and sags in the underlay
  • note where pipes, flues or roof windows pass through

Read the roof from the garden

Work with a pair of binoculars from the ground, on a bright day, and look along each slope in turn rather than across the whole roof at once. The aim is to match what the loft showed to something visible on the outside, so keep the measurement from the loft in mind and look at the area it points to.

Slipped, cracked or missing tiles show as gaps and uneven lines. Lead that has lifted or split shows as a pale edge or a dark gap along a wall. Gutters that spill over the lip show as green or dark streaks below. A flat strip along a chimney, a ridge with open joints and a roof window with a loose edge are all places to look at with extra care.

Signs of a leaking roof describes the visible signs in more detail. Here the aim is narrower: to find the single spot that matches your loft measurement. A fault that is not visible from the ground is not ruled out. The ground view narrows the search and does not complete it.

Do not climb to confirm what you think you see. A ladder at the eaves to look at a gutter is a reasonable limit, and a slope is not a place to stand. If the spot is out of reach, a photograph with a zoom lens from the ground gives a roofer a better start than a guess.

From the garden, look for

  • slipped, cracked or missing tiles
  • lifted or split lead along walls
  • debris packed into valleys and gutters
  • cracked pointing around the chimney
  • loose edges round roof windows

Junctions where roofs let water in

A plain slope of sound tiles sheds water. Leaks can start where one roof element meets another. The places below are junctions where water that has passed the covering may have come in, which is why a search spends its time there once the slope itself has been ruled out.

A valley is the angle between two slopes, where both shed into one channel, so it takes the run-off of two areas of roof. Flashings seal the joints between the roof and an abutting wall, a chimney or a dormer cheek, and a lead flashing can fail at a joint or where it lifts away from the wall. A roof window has its own flashing kit around the frame, and a gap there lets water in around the glass.

Ridge and hip tiles are bedded on mortar or fixed dry, and a cracked bed or a loose tile on the line lets water in under the cap. Pipes and flues that pass through the covering carry a collar or flashing of their own, and a flat roof next to a pitched one has the joint between the two to check.

Lead is long-lived when it is correctly installed. MyJobQuote says correctly installed lead flashing "can last for over 80 years", so a failed flashing points to how it was fixed or detailed. What to do if your roof is leaking covers the immediate steps while the search goes on.

A hose test done from the ground

If looking has not found it, a water test can. The idea is to wet one small area at a time, from the ground, while someone indoors watches the loft or the ceiling. Start at the bottom of the suspect area and move up, wetting each patch for a few minutes before moving on, so that a drip can be linked to the patch that caused it.

The order matters. Testing the whole roof at once tells you nothing, because any wet spot could be the one. Testing from the bottom up means a leak that appears is caused by the patch being wetted at that moment and not by one above it, which has not yet been tested.

Use a garden hose with a gentle flow and no pressure nozzle, and keep to the ground or a firmly footed ladder at the eaves. Never aim a jet under tiles or into joints, because a strong flow can push water in that rain would not. A test shows where water can get in. It does not mean the roof is faulty at that spot, so read the result with the loft evidence.

Stop if water comes in somewhere near wiring or a light fitting, and keep clear of that area until it has been checked. The weather also matters, so do the test on a dry day and leave the roof time to dry before the next patch.

When to stop searching and call

Some signs mean the search should stop and a roofer should be called. A sagging or bulging ceiling can hold a lot of water. Water near wiring is dangerous, and that part belongs to an electrician. A stain that keeps growing after a dry spell may be plumbing or condensation. A leak that has not been found after a careful look from the loft and the ground needs someone who can get on the roof safely.

Roofs of older cement sheeting need particular care. The HSE says "If the building was built or refurbished before 2000, assume that there is asbestos in it" and "AC roofs are always fragile". Do not walk on sheets, and do not drill or break them while looking for a fault.

Send what you have to our WhatsApp line: the loft measurement, a few photographs and the dates and weather. We look at photos you send. The survey that follows is what settles where the fault is and what the roof needs, and one total price in writing follows it.

Emergency roof repairs covers making the roof safe when the leak cannot wait, and the same advice to photograph, measure and note the weather applies there too.

Finding a leak: five questions about method

01Why is the stain nowhere near the damaged tile?

Water that gets past the covering lands on the underlay and runs downhill along battens, rafters or the sheet itself before it drips. The entry point is upslope of the stain, and it can be some way to one side. Working back up the damp timber in the loft, and measuring from a fixed point, finds the spot more reliably than looking straight above the mark.

02How do I turn a loft measurement into a place on the roof?

Pick a fixed point you can find from outside, such as the chimney stack, a party wall or the ridge end. In the loft, measure from it along the ridge line and up the slope to the wet area. Outside, take the same two measurements and stand where they meet. A mark of chalk on the timber and a photograph help the next person find it.

03Does a hose test prove where the roof leaks?

It shows where water can get in when wetted in that way, which is useful evidence and not proof of the whole picture. Wet one area at a time from the ground, from the bottom of the suspect area upwards, with a gentle flow and a helper indoors. Never aim a jet under tiles, because a strong flow can force water where rain would not go.

04Which junctions are worth checking when the slope looks fine?

Check the valleys, the flashings around chimneys and walls, the surrounds of roof windows, the ridge and hip joints, and any pipe or flue that passes through the covering. Water meets a break in the covering at each of them. A flat roof next to a pitched one adds the joint between the two. A zoomed photograph from the ground gives a first view without climbing.

05When is a damp patch a job for a roofer and not a plumber?

A patch that grows after rain and shows beneath a section of roof points to the covering and is a roofer's job. A patch that appears in dry weather, near a pipe run or under a bathroom may be plumbing, and a patch on cold mornings may be condensation. A roofer's survey separates them, and an electrician is needed if water has reached wiring.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote