Call 01582 935272

Roof repairs

What causes a roof to leak?

A leak starts where the roof stops shedding water: at a damaged covering, a joint between two parts, or a gutter that cannot carry the flow away.

Get a written quote

Call 01582 935272WhatsApp us

Wind-torn membrane peeled back from a wet flat garage roof
PicturedWind-torn membrane peeled back from a wet flat garage roof.

The short answer

A roof can leak because tiles have slipped or cracked, a flashing has failed, a valley or ridge has opened up, a roof window seal has gone, or a gutter has backed up and pushed water behind the roof edge. The stain and the entry point can be metres apart, so the cause needs tracing.

A roof drawing with its parts named: ridge tiles, tiles, battens, underlay, raftersRidge tilesTilesBattensUnderlayRafters

The tiles, slates and underlay

A pitched roof sheds rain because each tile or slate overlaps the one below, and the layer underneath catches whatever gets past. Anything that breaks that overlap can let water reach the timbers. A tile that has slid out of its row leaves a gap, and a cracked tile can pass rain straight through its body. Both faults can be spotted from the pavement with binoculars, which makes a look from the ground a sensible first check before anybody goes near the roof.

Along the apex, ridge tiles are laid on a bedding of their own. Marley's note on fixings points out that since the 2015 amendments mortar "could no longer be relied upon as the only means of securing the roof covering", which is why ridge and hip tiles are now mechanically fixed against wind uplift. A ridge bedded in old mortar alone can crack and loosen, and rain can then enter below the cap.

Below the tiles sits the underlay, a second barrier against whatever the covering lets through. Underlay can tear or perish with age. When it has, a roof that seems sound from the street can still pass moisture to the structure beneath, which is one reason a roof gets read as a whole in a survey instead of tile by tile.

Where one part meets another

Leaks gather at junctions, because a junction is where two surfaces have to be sealed against each other rather than simply overlapped. The table sets out the places where that applies, and what can go wrong at each, with the ridge included since it caps the top of every slope.

Roof junctions and how each can let water in
JunctionWhat it doesHow it can leak
FlashingSeals the roof against a wall or chimneyLifts, splits or comes away from the brickwork
ValleyCarries water where two slopes meetLining wears or cracks, or debris holds water
Roof windowLets light in through the slopeSeal or surround flashing lets water past
RidgeCaps the top of the roofTiles loosen or the bedding breaks up

Lead is a familiar flashing material. MyJobQuote says correctly installed lead flashing can last for over 80 years, yet lead can still fail early where it was poorly fitted or where the mortar holding its upper edge has crumbled. The page on signs of a leaking roof describes what each of these faults looks like from inside the house, with the ceiling and wall marks that point towards them.

Gutters, ageing and the wrong place to look

Gutters are part of how a roof sheds water. For guttering, Brett Martin gives a fall of 1 mm for every 600 mm towards the outlet, so a section that has sagged or filled with leaves can hold water in place instead. Overflow from a blocked section can reach the fascia, the soffit and the head of the wall, and from there it can travel into the edge of the loft.

Age plays a part everywhere. Sealants shrink, fixings corrode and covering materials lose their surface over the years, so a roof can develop several small faults before any one of them shows indoors. When a stain does appear, it can sit well away from the entry point, because water can run along a batten or down a rafter before it drips. A patch placed directly above the stain does not always cure the problem for that reason.

The practical step is to note where and when the stain appears. A mark that grows during rain points to a roof or gutter fault, and the page on how to find a roof leak takes the checks in order. Where the roof needs more than a local fix, the roof repairs hub sets out the options available. Photographing each mark, with the date, gives the survey something concrete to work from.

Leak causes, asked plainly

01Can a roof leak with no missing tiles?

Yes. A flashing can lift, a valley lining can crack, a roof window seal can fail or an old underlay can tear, and none of those shows as a missing tile. Gutters that overflow can also send water into the roof edge. This is why a survey reads the whole roof, rather than only the covering, before any repair is suggested.

02Why does my roof only leak in certain winds?

Wind-driven rain can be pushed up under a lifted tile edge or against a flashing from one direction only. The same gap may stay dry in rain that falls straight down. A leak that appears on one side of the house during a blow is worth writing down with the date, because the direction narrows the search for the entry point.

03Do small leaks matter?

A small leak can soak insulation, rafters and ceiling boards for weeks before a stain shows. Damp timber can decay, and wet insulation can lose its effect. A drip that is easy to ignore is still moving water into the structure, so it is worth reporting early, with a photo sent to 07880 284133 on WhatsApp so the position can be seen. Keeping insulation and timber dry avoids a larger repair later.

04Is every wet patch down to the roof?

No. Condensation, a plumbing pipe or an overflowing tank can make the same stain. A mark that shows up only after rain points towards the roof or gutters, while one that shows in dry weather points elsewhere. The page on what to do if your roof is leaking covers the immediate steps to take, whichever it turns out to be.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote