Start with where the fault is
A roof window that leaks, mists or sticks is giving one symptom with several possible causes. Replacing the whole window answers every fault at once, and it is the right answer only when the fault sits in a part that cannot be put right on its own. The first job is to find which part is at fault, and that comes before any talk of price.
Roof windows are built from a sash, a frame, a sealed glazed unit, seals and a flashing that joins the frame to the surrounding roof covering. A fault in the flashing is a roofing repair at the edge of the window. A fault in the seals or the glazed unit is a window repair. A fault in the frame is the case where a new window comes into question.
The same stain on a ceiling can come from any of them, and condensation can pass for a leak, so a survey follows the water back to its source before anything is priced. A photo of the stain, and of the window from inside, can be sent on WhatsApp and looked at first. Each possible source can be ruled in or out in turn, and only then does replacement become the sensible route.
The reading order matters. A reader who jumps to replacement may pay for a new window when the flashing was the problem, and a reader who patches a frame that has softened may be back with the same stain.
Tracing a leak to its part
Where a leak shows is a clue to where it starts, though not a certain one, since water can travel along timber and insulation before it appears. A drip at the head, damp beside the frame, water on the inner sill, mist between the panes and a draught each point to a different part to check first.
| Where it shows | Part to check first |
|---|---|
| Drip from the head of the frame | Flashing and the covering above it |
| Damp beside the frame | Side flashing or a lifted edge |
| Water on the inner sill | Condensation, or a worn seal |
| Mist between the panes | The glazed unit |
| Draught round a closed sash | Seals, or a sash that has dropped |
Water on the inner sill needs care. Moisture that forms on the room side of cold glass is condensation, which comes from the air in the room and not from the roof. A window can show both condensation and a real leak, and the two can be confused, so the survey looks at the sill, the frame and the roof outside together.
A leak that appears only in some weather is also a clue. Water that comes in when the rain is driven against one slope points to a path that opens in that direction, such as a gap at the side of the frame, while a drip in every shower may point to the head. It stays a clue until the roof has been looked at, because a path for water can open at a joint in the covering well above the window and run down inside the slope to the frame.
Flashing kits and the covering round them
A flashing kit is the set of pieces made to join a roof window frame to the covering around it. Its shape depends on the covering, since tile, slate and flat profiles need different pieces. Its job is to send rain over the frame and on down the slope, and when it fails the water is let into the opening round the frame.
A repair here can mean refixing a lifted edge, dealing with covering that has slipped beside the window, or clearing the leaves and moss that have built up where the frame meets the covering above it. These are roofing repairs. The window is left in place, and the repair is judged on the flashing and the covering and not on the glass.
A kit that has split, or that was made for a different covering, calls for a new kit. A replacement window is the moment to look at the flashing again, because a kit made for the old window may not fit the new one. A window and its kit can therefore be priced together, as one written sum that the survey produces.
Lead is one material a flashing can be made from. MyJobQuote's chimney leadwork page says correctly installed lead flashing can last for over 80 years. The figure belongs to that leadwork and says nothing about the life of a particular roof window.
Seals and glazed units
The seals round the sash press against the frame to keep the closed window tight. When they harden or flatten, the joint lets air through, and in driving rain a few drops. Where the maker supplies the seal, replacing it is a repair that leaves the window in place.
The glazed unit is a different matter, and a harder one to see from outside. A unit whose edge seal has failed lets moisture into the gap between the panes, and the mist cannot be wiped away from either side. The unit is the fault, and in some windows it can be swapped on its own while the frame stays.
Whether that is possible depends on the make of the window and on whether a matching unit can be had. Where it cannot, or where the frame beside it is also failing, the choice moves towards replacing the window. A unit replaced inside a tired frame can leave the owner with a new pane in a window that fails again at the frame.
This is the most direct comparison between repair and replacement, because a seal or a unit has a clear price against a clear fault. Where a window's glass is the only trouble and its frame is sound, repair is worth weighing carefully against the whole cost of a new window.
Frames, sashes and when repair stops
A frame that has softened, swollen or corroded cannot be put right by changing the glass or the flashing. The frame holds everything else, so a fault there can spread to the seals and the gear. That is the point at which a new window is the sensible answer, not a patch.
Signs that point towards replacement rather than repair include:
- Soft or flaking timber at the lower corners of the frame, the low points where water collects.
- Corrosion on metal parts that has lifted the finish.
- A sash that has dropped out of square and no longer closes evenly.
- Hinges that bind because the frame has moved, not because they have worn.
- Staining on the timber round the opening that shows water has been getting in.
None of these proves a window is finished, and each can sit alongside a part that is sound. What they share is that the repair would have to be made to the frame itself, and a frame repair is harder to stand on than a seal or a flashing.
An owner can look at the timber round the opening from inside the room, or from the loft hatch, and that is part of the picture. Rot or staining in the rafters beside the window changes the job, since the opening itself may need work before a new window goes in. That is a finding the survey reports, and it is the reason any figure quoted over the phone for a replacement window is only a guide until the roof has been seen.
When replacement makes sense
Replacement makes sense when the fault sits in a part that cannot be dealt with alone, or when several faults add up. Each fault on its own may be a modest repair, and several together can come to more than a new window would, which is a fair comparison for an owner to ask for. The comparison is between what the roof window is now and what the repairs would leave it as, a window with some new parts and some old ones, each with its own remaining life.
| What is found | Route to weigh first |
|---|---|
| Flashing split, frame and glass sound | Repair the flashing and covering |
| Unit misted, frame sound | New unit, or a new window if none matches |
| Seals worn, nothing else | New seals |
| Frame soft or corroded | New window |
| Several faults at once | New window against the sum of repairs |
The last row is the one that needs thought. An owner who has been quoted three separate repairs can reasonably ask what a replacement would cost, so the comparison is between two totals and not between a heap of individual repairs.
How old the window is has a part to play, and our guide to how long roof windows last sets out which parts wear and what the signs are.
What a replacement has to meet
A replacement roof window is new fabric in an existing home, and Approved Document L (2021 edition) sets its performance in Table 4.2. For a roof window the entry reads 1.4 W/m²K or Window Energy Rating Band B minimum, with 2.2 W/m²K as the entry for a rooflight. Band B is a floor and not a target, so a window rated better than that is also acceptable.
Which row applies is settled by the definitions in the Approved Document. Appendix A defines a rooflight as "A glazed unit installed out of plane with the surface of the roof on a kerb or upstand", and a roof window as "A window installed in the same orientation as, and in plane with, the surrounding roof". A window set flush in a pitched slope is in plane, so the roof window row applies to it.
Building control is carried out by the council's building control team or by a registered building control approver, and the route for a particular job is checked with the council before work starts. Planning is its own question, apart from Building Regulations, and our guide to roof windows and Building Regulations goes through both.
Cost follows the same logic. Roof window and skylight costs gives MyJobQuote's dated figures for a new window and for a straightforward swap, and the price that follows a survey is a single written total, never a list. A window that is only a few years old with one worn seal is a different case from an old window with a soft frame, and the survey sets each out in its own terms.

