Start with where the fault sits
Before you weigh a repair against a new run, find out how widespread the problem is. A leak at a single joint is a local fault. Drips along several joints, cracks in more than one length and a run that sags in two places point to something that is general to the whole gutter.
A watering can or hose makes this easy to map. With the downpipe clear, pour water in at the high end and watch the run. Each drip, sag or overflow is a mark on a rough plan of the gutter, and a plan with one mark reads very differently from one with six.
Age and material come next. Plastic that has become brittle can crack along its length when it is touched. Cast iron or steel can rust through from the inside where it holds water, and a run in either material that is weeping in several places is wearing out as a whole.
Last, ask what the gutter is fixed to. A run that is sound but hangs from a rotten fascia is not a gutter fault at all, and repairing the gutter will not hold until the board behind it is dealt with.
- how many places leak, drip or sag
- the material and its condition
- whether the fascia behind it is sound
- whether water pools after the channel is clear
Faults a repair can cure
Some gutter faults have a direct fix. A joint that drips can have lost its seal, and a fresh seal at the union can stop it. A bracket that has loosened can be refixed or replaced, and a run that dips between two brackets can be lifted and held at the right height with an extra bracket.
A blocked outlet is a clearing job, not a repair. A cracked union or a single damaged length can be swapped for a matching part where one can be had. A missing stop end, a split corner piece or a loose downpipe connector can be renewed on its own without touching the rest of the run.
A repair makes sense when the fault is single, the rest of the gutter is sound and the fascia behind it is solid. It is also the right choice when the run is fairly new and the problem is a fitting or a seal rather than the material itself.
| Fault | Repair that can answer it |
|---|---|
| Dripping union | New seal or union piece |
| Sagging span | Refix or add a bracket |
| Cracked length | Replace that length |
| Missing stop end | Fit a new one |
A repair also has limits. Where the same joint has been resealed before and has failed again, the seal is not the fault. The gutter may be moving at that point, or the fall may be wrong, and a third reseal will not change that.
Signs a repair may be enough
- one leaking joint
- a single loose bracket
- one cracked length
- sound fascia behind
- run fitted fairly recently
Signs the whole run is done
A gutter that fails in many places at once is telling you that the material has aged. Cracks that appear in several lengths, joints that weep along the whole run and brackets that no longer grip are the pattern of a gutter near the end of its service.
Plastic that has been in sunlight for years can go chalky and brittle. It may crack under a hand pressed against it, and a repair to one length can leave the next to go. Rust on a cast iron or steel run is a similar sign, especially where it shows as flakes or holes, since the metal is thinning from within. A wrong fall is the other major reason. If water pools along the length and not just in one dip, the run was laid at the wrong slope or has moved, and a seal or a bracket cannot fix a slope. The whole run has to be taken down and refixed at a proper fall, which is closer to a replacement than a repair.
Size and layout can also decide it. A run that has overflowed in ordinary rain while perfectly clear may be asked to carry more roof than it was meant to, for example after an extension has been added. A longer run, an extra downpipe or a larger channel is a change of design, and that is a replacement job.
A gutter that has been patched repeatedly is a sign too. Each patch has a cost, and the total over a few years can come close to what a new run would have taken, without ending the leaks.
The fall: 1 mm in 600 mm
In its installation guide, Brett Martin says a gutter should be fixed sloping down to the outlet, 1 mm for every 600 mm. That is a very faint slope, about the thickness of a coin over the length of a bath. It is enough to move water along the channel, and a small error is enough to stop it.
Because the slope is so slight, a sag of a few millimetres at the wrong place can hold a pool. The bracket that has dropped, the stretch that has bowed under the weight of ice or leaves and the section that was never level can all do it. Water that stands in a channel leaves silt, grows moss and loads the brackets.
A level check shows the problem faster than the eye. A spirit level laid along a dry channel, with the fall allowed for, shows where the run is level or sloping backwards. A run that slopes the wrong way over a long stretch cannot be cured with sealant.
| What you find | What it can mean |
|---|---|
| One shallow dip | A dropped bracket; refix may do |
| Pool along a whole run | Laid level or sloping backwards; re-lay |
| Water stands at the outlet end | Outlet set too high; reset |
Where the fall is out along the whole run, refitting it properly means removing the gutter and fixing it again at the right slope, which is why it points towards replacement.
You might hear
A gutter needs to be perfectly level to hold water.
Plain as day
It needs a gentle fall towards the outlet: 1 mm for every 600 mm, says Brett Martin.
What lies behind the gutter
The fascia is the gutter's backbone, so its condition can settle the repair-or-replace question. Brackets screw into it, and if the board is soft the screws have nothing to bite. A gutter fixed to rotten timber will sag again within a short time whatever has been done to the channel.
Press a thumb into the underside of the board and at its cut ends. Timber that gives, or a surface that crumbles, means rot. The board needs repair or replacement first, and the gutter is refitted afterwards. That order is why a quote for new gutters on a roofline with a soft fascia can grow when the old run comes off.
Older houses add a safety check. HSE says a property built or refurbished before 2000 should be assumed to hold asbestos. HSE classes asbestos cement items, rainwater goods among them, as non-licensed work, provided they come off carefully and in one piece. A cracked or broken old gutter or soffit is not a job for a scrubbing brush or a drill, and a board that might be AIB needs identifying before anyone works on it.
The roof above the gutter matters too. A slipped or missing tile at the eaves can send rainwater down behind the gutter and onto the fascia, and a gutter repaired beneath a roof fault will keep suffering until the roof is put right.
Weighing the cost of each
A repair is smaller than a replacement, but the cheaper job on the day is not always the better choice over a few years. A repair to a gutter near the end of its life can be followed by another repair nearby, and the repeat call-outs can add up. A replacement removes the whole class of problem in one go.
For scale, MyJobQuote's average for replacing gutters is around £1,000 to £1,600, and the page carries the date 20 October 2026. Which? Trusted Traders put clearing out a house's gutters at £75 to £350, excluding VAT, in November 2025. Those two figures describe very different jobs, and neither of them prices a gutter repair. The costs guide sets the sourced figures out.
A repair quote and a replacement quote should both say what they include. For a repair, that means which fault is being treated and whether the fascia is looked at. For a replacement, it means which sides of the house, whether downpipes are renewed and what happens if the board behind is found rotten.
Material counts here as well, since a new run need not match the old one in material, and the uPVC, aluminium or cast iron guide covers the choices for a new run. Colour and profile are worth settling at the same time, because a new run on the front of a house sits beside old boards and a mismatch shows.
Getting a clear answer on yours
The surest way to settle the question for your own gutters is to have the whole roofline looked at, not just the leaking joint, because the answer depends on how many faults there are and what the fascia is like. The survey takes in the whole roofline, and afterwards you hear in plain words what turned up, other faults included, and whether a repair will do or a new run makes more sense. One written total price follows after that.
Where the eaves are high, a scaffold may be needed, and where it stands on the road or pavement we arrange the licence with our scaffolder. That scaffold belongs to the one price you are given.
A photograph is a good start. Send one of the whole run from a distance, one of the worst joint and one of any stained board to 07880 284133 on WhatsApp, or call 01582 935272. Note which places drip in rain and which stay dry, since a plan of the faults helps more than a single close-up.
The signs your gutters need work guide is a useful companion, because each sign on its list can point either way depending on how widespread it is.

