The short answer
A soffit is the panel fixed across the underside of the roof overhang, reaching from the brickwork to the fascia board. It shuts off the space above so that birds and weather stay out, and it can carry vents that let air into the loft. On older houses the panel may be asbestos insulating board.
What a soffit is and where it sits
Where a roof overhangs the wall, the rafter ends stand clear of the top of the brickwork. Rafters are the angled timbers that form the frame. The soffit closes what lies between. It reaches from the wall outwards to the back of the fascia, and it is the only part of the eaves you see when you look straight up from underneath. It can be a plain board, or a board with slots or holes cut into it.
A soffit is paired with the fascia, the board that faces outwards and carries the gutter, which is covered on the what is a fascia board page. The fascia is vertical, seen from the front, and takes the weight of the gutter. The soffit is horizontal, seen from below, and carries no load of that kind. The two are fitted together, so a job that touches one can reach the other.
- Shuts off the space above, between the wall and the roof frame.
- Keeps birds, wasps and weather out of the roof space.
- Can carry vents that bring air into the loft.
- Gives the eaves a finished underside.
The name can also be used for the underside of other overhangs, such as a porch roof or a bay. The idea is the same each time: a panel that finishes whatever projects and hides the timber behind it. The word turns up in surveys and quotes, so it helps to know it.
Why ventilation runs through it
A soffit does more than tidy the eaves. In a ventilated roof it is also where fresh air enters the loft. Vents can be cut into the panel as a continuous strip or as round discs, and air entering there helps to carry moisture out through the ridge or the covering, which keeps the roof timbers dry.
The figures come from Marley, a tile maker, working from BS 5250. Its eaves openings depend on the pitch and on the underlay: one size for pitches of 15° or less, a smaller one above 15°, where the underlay is high-resistance in a cold roof. With a low-resistance underlay and a well-sealed ceiling, Marley says that "fortuitous ventilation at the eaves via normal eaves construction (3mm) is all that is required", provided UKAS third-party certification requirements are met.
A soffit can be blocked without anyone noticing. Paint or insulation pushed hard into the eaves, or a replacement panel with no vent in it, can cut off air the roof was designed to receive. When soffits are being replaced, ask what ventilation the new panels will give, and compare it with the roof as built. A vented panel does little good if insulation sits against it.
Materials, ageing and the asbestos question
Soffits have been made from timber, plywood, uPVC, aluminium and cement-based boards. Timber and plywood can rot where gutter water reaches them. uPVC panels can sag, discolour or crack. Each type suits different houses, and the how long fascias and soffits last guide compares what each source gives.
Age matters here for a safety reason. HSE lists "AIB white soffit panels to underside of roof eaves" among the places asbestos insulating board is found, and advises: "If the building was built or refurbished before 2000, assume that there is asbestos in it." HSE says most work on asbestos insulating board is licensed work. A panel that might be asbestos should not be drilled, broken or sanded, and anything that could be asbestos is identified first. Asbestos waste goes in a lockable skip, never an open one.
The asbestos soffits guide goes through what to do on an older house, and the guttering, soffits and fascias hub shows how all the parts fit together. A price comes after the survey and is a single written total, so you can compare it with what the guides describe before agreeing to anything. Where the eaves are out of reach from the ground, scaffold is part of that one total.

