Call 01582 935272

Guttering, soffits & fascias

Why is my gutter leaking at the joints?

A joint is where two lengths of gutter meet, which makes it the weakest point on the run. A failed seal, a sagging bracket or a shifted length can each let water escape there.

Get a written quote

Call 01582 935272WhatsApp us

Rainwater running off a slate roof into a cast iron gutter
PicturedRainwater running off a slate roof into a cast iron gutter.

The short answer

A gutter can leak at a joint because the seal between two lengths has perished, because sagging brackets have pulled the lengths apart, or because the run has shifted as temperatures change. Water then drips from the joint instead of reaching the outlet. A fresh seal can cure a simple leak, while a run that has moved needs refixing or replacing.

A roof drawing with its parts named: gutter, fascia, soffit, underlay, rafterGutterFasciaSoffitUnderlayRafter

What a gutter joint has to hold back

Gutters are made in lengths, because a single piece long enough for a whole roof edge would be impossible to carry or fix. The lengths are joined end to end. In a uPVC system the join is a union bracket, a small clip-on piece that wraps both ends and holds a rubber seal around the meeting point. In cast iron, the ends are bolted together through a flange with sealant bedded between them. Aluminium systems use their own jointing pieces and sealants.

Each of these joins has the same job. It has to let water pass straight across from one length to the next, and it has to stop that water slipping out below or at the sides. The seal does this by pressing against both ends. If the ends move apart, or the seal hardens and shrinks, a gap opens, and the water running along the bottom of the gutter drips out through it.

A joint also has to cope with movement. Plastic lengthens in warm weather and contracts in cold, so a long uPVC run is a slightly different length in July than in January. A well-made joint lets the ends slide a little without opening. If the lengths are pushed hard against each other, or fixed so tightly that they cannot slide, the strain can crack a bracket or squeeze the seal out of place. The comparison of uPVC, aluminium and cast iron shows how the three materials behave differently.

Why a joint starts to drip

A joint can fail for more than one reason at once, and one fault can make another worse. The possible causes are listed below, though no list can say which applies to a particular house.

  • A rubber seal that has dried, hardened or perished with age.
  • Silt or grit trapped in the joint when it was assembled, which stops the seal pressing flat.
  • A bracket that has sagged, so one length hangs lower than its neighbour.
  • Fixings that have loosened where the fascia behind has softened.
  • A union bracket that has cracked.
  • A fall set the wrong way, which pushes water towards a joint in place of the outlet.
  • Cast-iron sealant that has cracked or shrunk back from the flange.

Where the drip lands tells you something. A leak that appears at the same point in every shower, and stops soon after the rain does, points to a joint. A leak that only happens in very heavy rain, or comes over the front edge along a whole stretch, may be an overflow caused by a blocked outlet instead. Algae or a dark mark on the wall directly under one joint points to a slow drip that has run for a long while. The signs your gutters need work guide covers the other warning marks.

Resealing, refixing or replacing

The right repair depends on why the joint is leaking. A perished seal on a gutter that is otherwise straight and sound can be cleaned out and resealed, or a worn union can be swapped for a new one. A sagging bracket is refixed to firm timber, which brings the lengths back into line so that the joint closes again. A cast-iron flange can be cleaned back, rebedded and bolted up.

Sometimes the joint is only the place where a bigger problem shows itself. Lengths that have warped, a fascia that is rotting behind them or a gutter that has lost its fall will keep leaking after a reseal. The repair or replace guttering page explains how to weigh the two, and the slope of the run matters to every joint along it, because water sent the wrong way leans on the weakest seal.

On cost, MyJobQuote gives "The average gutter replacement cost in the UK is around £1,000 to £1,600." That is a national average for replacing a whole system from a page dated 20/10/26, and a single joint repair is a very different job. Your own gutters are priced after the survey as a single written total, with any access the eaves need included in it. The guttering, soffits and fascias hub gathers the related guides in one place.

Leaking joints, explained plainly

01Can I stop a leaking gutter joint with sealant myself?

A dab of sealant on the outside of a joint may slow a drip for a while, but it leaves the cause in place. If the seal inside has perished or the lengths have moved apart, the water keeps getting through. A ladder resting on the gutter itself is not safe, because a gutter is not built to take that load.

02Why does the joint only leak when it rains hard?

A small gap may stay dry while a trickle runs along the bottom of the gutter, and spill only when the flow deepens in a heavy shower. A blocked outlet can produce a similar picture, since water backs up and spills at the lowest weak point, which can be a joint. Clearing the outlet is the simpler check, and if the joint still drips afterwards, the seal or fixings are the likely cause.

03Is a leaking joint a sign the whole gutter needs replacing?

Not necessarily. One tired seal on an otherwise straight run is a small repair. A run with several leaking joints, a sag along its length or soft fascia behind it points towards something bigger. The pattern matters more than any single drip, so it is worth looking along the whole run, and at the board behind it, before deciding on a repair or a replacement.

04Does a leaking joint damage the wall or the fascia?

It can. Water that keeps dripping from a joint can run down the wall, leave stains and keep the brickwork wet. It can also soak the fascia and soffit above it, and timber that stays wet can soften over time. If an older soffit is involved, read the asbestos soffits guide before anything is disturbed, since older soffit panels can contain asbestos.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote