What a valley does
Take two roof slopes that meet at an inward angle and run down to the eaves: the line where they join is a valley. Rain that lands on both slopes is steered towards that angle, so the valley carries the run-off from two roof surfaces along a single channel. Its lining is a waterproof sheet, lead on the roofs this post covers, laid in the angle beneath the edges of the tiles or slates.
Valleys can be found on houses with an L-shaped plan, with a rear extension joined to the main roof, or with a dormer or bay that adds a second ridge. A roof of that shape can have a valley, whether the house is in Dunstable, Leighton Buzzard or Biggleswade. Which roofs have lead in the valleys and which have another lining is something only the roof itself shows, and the town it stands in settles nothing.
That is also why an older roof deserves a close look at its valleys, and why a valley is worth a look whenever a ceiling stain appears below one. The tiles either side can be sound while the lining under their edges has split, and the evidence may sit on a ceiling below, with nothing to see on the roof from the garden.
The parts of a lining
A lead valley is made of a handful of parts, and each can be the one that fails. The lead sheet is laid in lengths down the angle. Where one length meets the next, the sheets overlap, with the upper length laid over the lower so that water running down the valley passes onto the next sheet and not beneath it. Those overlaps are the laps. The timber boards or battens below hold the lead up, and the edges of the tiles or slates lie over the sides of the lead, covering its margins. At the bottom, the valley empties into the gutter.
The strip lists those parts in the order the water meets them as it runs down the angle. A fault in any of them shows up as the same symptom indoors, so the survey has to look at each.
A lap that has opened lets water run beneath the sheet, where the boards take the wetting and carry it on. Lead that has lifted at its margin lets wind-driven rain blow under the tile edge. A board that has gone soft lets the lead sag and hold a pool. A gutter that has blocked at the valley's outlet backs water up the valley itself. Four different faults, one stain on the ceiling, which is why the stain alone cannot name the cause.
Parts of a lead valley
- Lead sheet lining
- Laps between lengths
- Boards beneath
- Tile or slate edges
- Outlet into the gutter
Lead codes and thickness
Lead sheet comes in codes 3 to 8 to BS EN 12588, and each code stands for one fixed thickness of sheet: the higher the code, the thicker the sheet. Code 4, for example, is 1.80 mm. The weight charts of the makers Calder and Ecobat run against the same codes, and their weights differ for code 3 and code 6, so any weight needs the maker named beside it. The table gives thickness for each code, with the weights from Calder's chart.
| Code | Thickness | Calder, kg per m² |
|---|---|---|
| 3 | 1.32 mm | 14.97 |
| 4 | 1.80 mm | 20.41 |
| 5 | 2.24 mm | 25.40 |
| 6 | 2.65 mm | 30.05 |
| 7 | 3.15 mm | 35.72 |
| 8 | 3.55 mm | 40.26 |
A table of thicknesses cannot choose a code for a valley. Whatever code the roof's specification names for that detail is the one that goes in, and the valley is one detail among several on the roof. A roofer reading an old valley can measure what is there, yet the new lining is specified rather than guessed, and a thicker sheet is not automatically the right one. The page on lead sheet codes explained sets out the codes in more depth.
Signs on an older roof
From inside the house, a brown or yellow stain on a ceiling that follows a line under a valley is a clue. So is a damp patch on the wall of an upstairs room where a roof slope meets a gable. After a heavy downpour, a torch shone from the hatch can reveal wet timber beneath the valley line. Looking from the loft hatch is safe. Walking about on the joists is not, and a householder should stay on the hatch ladder.
Using binoculars from the ground, inspect the valley for a mat of moss or a drift of leaves lodged in the angle, because debris holds water against the lead. Look at the tile edges either side for slipped or cracked tiles. Look at the valley's outlet where it meets the gutter, since a gutter that has overflowed at that point sends water back to the valley. A dark streak on the fascia or wall at that spot points the same way.
On the roof itself, a surveyor looks for sheet that has cracked along a fold, lifted at its margins or opened across a lap, and for sealant or mortar smeared over a join, which can hide a failed lap. Not every stain has a valley behind it, so the survey traces the damp back to where it starts and judges the valley against that, instead of settling on the first suspect it meets.
Checks for a suspect valley
- Ceiling stain under the valley line
- Wet timber in the loft
- Moss or leaves in the angle
- Slipped tile edges
- Split or lifted lead
How long a lead lining can last
MyJobQuote says that correctly installed lead flashing "can last for over 80 years", with the same page adding over 100 years for higher codes. It describes lead flashing in good conditions, on a page last updated on 22 September 2026. It says nothing of a particular valley, and a figure for flashing is no promise for a lining. The word "can" in that sentence carries weight, and it should stay attached to the figure whenever a long life is quoted.
What matters on an older roof is that a long-lived material can sit on a short-lived support. The lead may be sound while the boards beneath it have softened, or the lead may be sound while the tile edges above it have shifted. A valley is therefore judged on its present condition, with each part checked in turn, and the age of the house does not settle it either way. A roof of any age can have a sound valley, and a recent repair can hide a poor one, so the lead is looked at as it is today.
The figure above is for flashing, and the page on how long lead flashing lasts goes through what that figure covers and what it leaves out.
You might hear
A lead valley never needs checking.
Plain as day
MyJobQuote's figure is for correctly installed flashing, which it says can last for over 80 years.
Patch, reline or replace
A small split at one fold can sometimes be mended with a patch of lead, while a lining that has cracked at several laps points to a new one, and the survey says which of the two the valley in front of it needs. Relining a valley means lifting the tile or slate edges along both sides, which is why the cost depends on the valley's length, taking out the old lead, checking the boards, laying new sheet in its place, and relaying the edges over it. It is slower and more careful work than a patch, because the tiles have to come back in line.
A sealant smeared over a split is a cosmetic fix and not a repair of the lead itself. The page on repairing or replacing lead flashing covers the choice, and the same thinking carries over to valleys.
The price for a valley comes after the survey, as a single written figure for the whole job. MyJobQuote's published lead figures for a chimney, a patch at around £200 and a full replacement around £570, belong to chimney leadwork and are not valley prices. Valleys vary in length, in the number of laps and in how they are reached, so a figure for one roof cannot be read across to another.
What a survey checks
A roof survey for a suspect valley looks at the lining along its full length, from the ridge end to the gutter. It checks the lead, the laps, the margins under the tile edges, the boards wherever they come into view and the outlet at the bottom, together with the timbers a damp stain leads towards. The survey also follows the damp back from the ceiling stain, so that the valley is judged against what the household has seen indoors, and against any earlier repair that is visible along its length.
Other faults noticed on the way across the roof, a displaced tile or a damaged ridge for instance, are put to you in plain terms, and the quote that follows is given as a single written sum. Reaching a valley can mean a roof ladder, a tower or a scaffold. In Dunstable, scaffolding on a footway or in a road falls under Central Bedfordshire Council's licensing as the highway authority for the road. We arrange the licence with our scaffolder.
A photograph of the ceiling stain or the valley, sent to WhatsApp on 07880 284133, is looked at, and 01582 935272 is the number for a call. The wider range of work is under lead roofing.

