Call 01582 935272

Chimney repairs

What is a chimney back gutter?

The back gutter is a small lead channel on the uphill side of a chimney stack. It catches the water running down the slope and carries it round the stack instead of into the joint.

Get a written quote

Call 01582 935272WhatsApp us

Rainwater running off a slate roof into a cast iron gutter
PicturedRainwater running off a slate roof into a cast iron gutter.

The short answer

A chimney back gutter, also called a cricket, is a channel behind a stack on the up-slope side, which can be formed in lead. It catches rain running down the roof and carries it round both sides of the stack. When its lead splits or lifts, water can get through to the ceiling and the roof timbers.

A roof drawing with its parts named: pots, flaunching, step flashing, apronPotsFlaunchingStep flashingApron

Where the back gutter sits and what it does

A stack rises through a sloping roof like a rock in a stream. Rain running down the slope hits the uphill face of the brickwork, and with nowhere to go it would pool against the joint where brick meets covering. The back gutter prevents this. It is a shallow channel dressed behind the stack, set to fall towards each side, so water arriving at the uphill face is carried round the stack and back onto the slope below.

The channel is formed in lead, which can be bent to the shape of the stack and the tiles. The sides of the channel turn up the brickwork, and its edges are tucked into a cut slot in the mortar. At each end the lead joins the side flashings, so that the whole collar of metal around the stack works as one watertight piece. Because the lead is dressed by hand, the quality of the folds decides how well it sheds water.

Roofers also call this detail a cricket, and some use the word for a ridge of timber or mortar behind the stack. The chimney flashing and leadwork guide covers the other lead pieces that sit around the stack, and the chimney repairs page puts them in context.

How lead is specified and how it fails

Rolled lead sheet is made to BS EN 12588 in codes 3 to 8, with code 4, for example, 1.80 mm thick, and the specification sets the code for each detail. A back gutter takes the full run of the slope's water, so the code is matched to the width of the stack and the flow it must carry, and that choice goes into the specification. A heavier code means thicker sheet.

MyJobQuote says correctly installed lead flashing "can last for over 80 years", and the same page adds over 100 years for higher codes. That describes good work, not a promise for every roof, because movement, poor dressing and neglect can all cut a life short. Signs that the channel has started to fail include:

  • A split or crack along a fold in the lead.
  • An edge that has lifted out of the mortar slot.
  • A dip in the channel where water now stands.
  • Open joints at the corners where it meets the side flashings.
  • Debris, moss or leaves packed in the channel.
  • A tide mark on a ceiling or on the chimney breast below.

A stain inside takes time to appear, so a small split can pass unnoticed for a long while. The chimney leaks in wet weather guide shows where water gets in and where it can travel before it shows.

Repair, replace and what it costs

A small split in sound lead can be patched. Lead that has cracked in several places, lifted from the brickwork, or sunk out of its fall is replaced, and the mortar slot is cut and re-pointed to take the new edge. Both jobs call for access at the stack, which means a ladder or a scaffold; if the poles have to stand over the footway beside the stack's house, we arrange the licence with our scaffolder.

MyJobQuote's page on chimney leadwork, last updated 22 September 2026, says that a patch repair to chimney lead flashing typically costs around £200, while a full chimney lead replacement averages around £570. Those figures cover chimney leadwork only, never lead laid on a flat roof or in a valley, and they sit beside our own written total rather than standing in for it.

A stack with a failed back gutter may also have worn flaunching or pointing, so the survey weighs the whole stack before any price is set. What we give you afterwards is one total, in writing. The chimney repair costs guide goes further into what moves the number, from the height of the stack to the state of the brickwork.

Back gutters, question by question

01Is a back gutter the same as a cricket?

In chimney work the two names point to the same detail: the channel behind a stack on the up-slope side. Cricket is the trade word, and back gutter is the plainer description of what it does. Some roofers use cricket for a raised saddle of timber or mortar instead, so ask which kind is meant when a quote uses the word.

02Can a split back gutter be sealed with a tube of sealant?

A smear of sealant can cover a split without closing it, and it ages faster than lead does. Lead that has moved or cracked is better mended with a fresh piece of lead, or replaced outright. Sealant laid over a failing channel can also hide the damage, which makes the real extent of the fault harder to judge later on.

03Does every stack need a back gutter?

A stack whose upper face meets no running water may not need one, because there is nothing to divert. A stack set part way down a slope has water arriving at its uphill face, which is the situation a back gutter exists for. The survey looks at where the stack sits on the roof before deciding what the detail needs.

04Where would a failed back gutter show indoors?

A mark on a ceiling or on the chimney breast near the stack's position is one place, though water may travel along timbers before it appears. Damp in the loft beside the brickwork is another, and so is a drip into a fireplace after rain. If you notice any of these, take a photo and message it to 07880 284133 on WhatsApp, or ring 01582 935272.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote