What Building Regulations ask of a flat roof
Building Regulations set standards for the work itself: that the structure carries the load, that the roof is safe in a fire, that water drains away and that heat is not lost through the roof any faster than the rules allow. They apply to the building work whether the house sits in a street of near-identical roofs or alone in a field, and they operate separately from planning permission.
A flat roof is a place where several parts of the rules meet. The covering keeps water out, the fall decides where water goes, the insulation sets the heat loss, and a kerb or a rooflight sets its own energy figure. A job that looks like a simple re-cover can touch all four, which is why it is worth knowing which test applies before the first quote is accepted.
| Question | Where the answer comes from |
|---|---|
| Is an application needed? | The Planning Portal's re-roofing test |
| What must the roof lose in heat? | Approved Document L |
| What fall must it have? | BS 6229:2025 |
| What about a rooflight? | AD L Appendix A and its tables |
The flat roofing section sets out the coverings that these rules apply to, and each test has its own figure or condition.
The Portal's two limits on a flat roof
The Planning Portal's re-roofing guide gives the test for when an application is needed. Work that affects "Less than 25 per cent of the total 'building envelope'" and for which "Less than 50 per cent of the roof is affected" does not normally need an application, in the Portal's words, and both limits must hold together. The word "normally" belongs to the Portal and stays attached to the test.
On a flat roof the second limit is the one that bites quickly. A garage roof, a single-storey extension roof or a porch roof can be the whole of the roof in question, so replacing the covering touches all of it. Go past either limit and an application is needed, which puts a full flat roof replacement on the application side of the line.
Put the other way round, a small patch repair to one corner sits inside both limits, being a fraction of the roof and a smaller fraction of the envelope. The envelope takes in floors, walls, windows and doors as well as the roof, so on a single-storey roof the first limit is not the one to worry about.
The Portal's main page for re-roofing says: "In most situations, this work will need Building Regulations approval." That sentence frames the whole subject, and the limits above describe the exceptions. When it is unclear which side a job falls on, the council's building control team can say.
A new membrane counts as renovation
Approved Document L, the volume covering fuel and power in dwellings, deals with existing roofs in two ways. Fabric newly added to a house is held to one table of U-values. Elements that already exist and are being renovated are judged on a second table, and a flat roof whose waterproof layer is stripped and replaced lands in that second group.
The text is direct: renovation includes "Replacing the waterproof membrane on a flat roof." Para 11.3 of AD L 2021 sets the trigger: once more than 50% of a roof's area is renovated, the whole roof is brought up to the later standard where feasible, which means the old insulation is examined and, where it falls short, added to.
- renovating over half of a roof: the whole roof is brought up to standard where feasible
- the test is the surface area of the roof, not the cost of the job
- a patch repair sits well below the line
- a full re-cover of a small flat roof crosses it
Because a new membrane on a small flat roof covers the whole surface, a garage, a porch and an extension roof all meet the rule. The question of where the insulation goes follows from that, and the guide on warm and cold flat roofs explains the options.
Table 4.3: 0.35 and the improved 0.16
AD L's Table 4.3 states how far a renovated roof should be improved. For a roof the table names two numbers: 0.35 W/m²K as the threshold and 0.16 W/m²K as the improved value. A roof above 0.35 is upgraded to 0.16 where feasible, while the other table in the document applies only to new fabric.
Feasibility has its own test, in para 4.13. If reaching the improved value would be impractical in the building, or would not achieve a "simple payback of 15 years or less", the upgrade goes as far as feasibility allows, aiming at a payback not exceeding 15 years. After an upgrade, AD L also says an element should not carry a U-value higher than 0.7 W/m²K.
A designer works these figures out from the layers of the roof, and they depend on the insulation material, its thickness and the way it is fitted. A quote that says only "insulated" has not said what U-value the roof will reach. Ask what it is, and look for the insulation and its thickness in the written quote.
AD L 2026 applies from 24 March 2027, with its tables renumbered 3.2 and 3.3. Until that date the 2021 edition, with its 2023 amendments, governs work in England, and the survey says which edition applies on the date of the work.
Falls under BS 6229:2025
A flat roof sheds water to outlets or gutters, so it needs a fall. BS 6229:2025 is the standard for flat roofs with continuously supported flexible waterproof coverings, and it replaces the 2018 edition, which has been withdrawn. NFRC says it asks for "a minimum 1:80 finished fall for general roof areas and internal gutters".
IKO adds a point about design: "To achieve a 1:80 fall, the code of practice says that the roof should be designed for a fall of 1:40". The two figures belong together, because a roof designed to 1:40 still lands at or above 1:80 after the deck, the boards and the laying have allowed for tolerances.
The standard deals with membranes such as single-ply sheets, felt and the like, and it does not deal with lead. Water lying on the roof after rain shows that the fall is wrong somewhere, or that an outlet is blocked. Any shortfall in the deck stays in place beneath a new covering, so the survey measures the fall before a covering is chosen.
Where the fall is short, tapered insulation or new firrings can build the slope in, and that links with the renovation rule above, because the insulation is being renewed anyway. The page on the minimum fall for a flat roof goes into the arithmetic.
Rooflights on a kerb, and roof windows
A glazed unit in a flat roof is judged by what it is. Appendix A of AD L gives a rooflight its meaning with the phrase "out of plane with the surface of the roof on a kerb or upstand". A lantern or a skylight on a kerb in a flat roof is a rooflight, and for a replacement the table gives 2.2 W/m²K.
A roof window is a different thing. It is a window installed "in the same orientation as, and in plane with, the surrounding roof", and its figure is 1.4, or Window Energy Rating Band B minimum. A roof window suits a pitched roof or a slope, not a kerb in a flat roof. The words skylight and roof window are not interchangeable in a U-value sentence, so a quote should say which unit is meant.
A rooflight on a flat roof also needs a kerb that is waterproofed as part of the covering, with its own upstand and flashing. A new covering is the time to deal with that, since the kerb has to be taken into the membrane. The comparison of EPDM, GRP and felt explains how each covering finishes at an upstand.
If a glazed unit is going in or coming out as part of the roof job, mention it when the roof is first looked at, so that the correct U-value is on the written quote from the start.
Who checks the work, and what we do first
Building control is carried out by the council's building control team or by a registered building control approver. A private approver must appear on the Building Safety Regulator's register, and that registration regime began on 6 April 2024. The council's team issues a completion certificate at the end. A registered approver issues a final certificate.
File whichever certificate arrives with the deeds or house papers, as proof that the roof work went through building control. If one cannot be found years later, ask the council's building control team what it holds on file for the address.
On our side, the roof is surveyed before a quote is given, and we check the building control route with the council before work starts. Which route applies depends on the roof, the share of it renovated and the insulation proposed, and the survey brings those together. The firm reports what the roof showed and what else was noticed there, and a single total is then put to you in writing.
If you have a flat roof in mind, send a photograph on WhatsApp on 07880 284133 or call 01582 935272. The photograph helps with the first look, though the Building Regulations question is settled on the survey.

