Why a covering needs a dry deck
Every flat roof covering is laid onto a surface and sealed over it, and that surface has to be dry. Water left in the boards, or on top of them, does not disappear under a new membrane. It stays there, and a covering sealed over damp can lift into the bubbles described in our guide to flat roof problems. A blister made this way is a fault built in on the day.
Rain is the obvious enemy, but it is not the only one. Morning dew, a layer of frost and the film of damp that settles on a cold board overnight can all leave a deck wet to the touch while the sky looks clear. A roof that looks dry from the ground can be wet where it matters, which is at the surface the covering will bond to.
That is why flat roof work is scheduled by the weather as much as by a date. A roofer who lays a covering onto a damp deck to keep to a schedule has saved the schedule and spent the roof. Where a job has to wait for a dry spell, the wait is part of doing it properly, and a quote that has no room for it has not allowed for the season.
Even a deck that is dry in the morning can be soaked by afternoon, so the covering is laid in sections that can be finished and made watertight before the weather turns.
What cold does to adhesives and resin
Coverings differ in how they are fixed, and cold affects each one in its own way. EPDM rubber is a sheet that is bonded to the deck with adhesive and joined at the seams. GRP is built from resin and glass fibre that set by a chemical reaction on the roof. Torch-on felt is melted onto the layer beneath. Each of these fixings has working conditions set by its maker.
Adhesive that is applied to a cold or damp surface may not grip as it should. Resin that is laid when the deck is cold can set slowly, or set poorly. A cold sheet is stiffer to handle and less willing to settle into a corner or fold around an upstand. These are matters of method rather than rules of thumb, so the product's data sheet, not a guess, decides whether the conditions on the day are acceptable.
Manufacturers publish their own limits for adhesives, resins and primers, and a roofer working to those limits will sometimes decline to lay a covering on a given day. That is a sign of a firm following its materials' instructions.
- a deck that is wet, frosted or visibly damp
- rain forecast before the covering has been sealed
- adhesive or resin used outside its published limits
- seams and laps made on a cold, stiff sheet without checking they have bonded
Rain, exposed decks and covering up
A flat roof is at its most vulnerable while the old covering is off and the new one is not yet on. The boards are bare, the edges are open and anything that rains in has a clear path to the ceilings below. The risk is not abstract: a deck that is soaked in the middle of a replacement can delay the whole job.
Work on a stripped roof is therefore planned in parts, with only as much exposed as can be sealed again before the weather changes. Sheeting that is fixed down firmly over the open deck at the end of a working day is one way to keep a stripped area from taking on water. Sheeting that is loose can flap, lift and let the rain under it.
Boards that have been soaked can be left to dry before the covering goes on, and boards that have been wet for too long can need replacing. A roof opened in a wet week may reveal more damage than a roof opened in dry weather, because water has had time to reach the timber. The survey cannot tell what the weather will do, but it can tell how the deck looks now.
Dry weather helps the decision as much as the work. A roof opened in a wet week may be covered over again, rather than finished, and the work picked up when the deck has dried. That is a reasonable thing for a roofer to do, and a reason to ask a firm how it handles interruptions before work starts.
Temporary covers and what they are for
A temporary cover is a stopgap that keeps water out of a roof until the weather allows a proper repair. It may be a heavy-duty sheet fixed over a split, a patch bedded onto a failed section or a tarpaulin held down across a damaged area. Whichever it is, the purpose is the same: to stop the interior taking more water while the real fix waits.
A temporary cover is not a repair. Sheeting can slip in wind. A patch laid over wet felt may not bond. Sealant applied to a damp surface may fail within days. Each of these can hold for a spell, and none should be left in place as the roof's permanent answer, because the underlying fault is still there.
| Cover | What it does | Its limit |
|---|---|---|
| Fixed sheet | Keeps rain off a damaged area | Can lift in wind if the edges are not secured |
| Bedded patch | Covers a split or a failed join | May not bond to a wet surface |
| Sealant or tape | Bridges a small gap | Works only on a clean, dry surface |
If water is coming in, catch the drip in a bucket and keep furniture and electrical items clear of it. Do not climb onto a wet or icy flat roof to place a cover yourself. A photograph of the stain and the roof, sent to 07880 284133 on WhatsApp, lets us look at what is happening before anyone decides what to do.
Ice, ponding and frozen outlets
Standing water on a flat roof can freeze, and ice does damage in ways that liquid water does not. It can block an outlet, so that melt water has nowhere to go and backs up behind the ice. It can also push on a seam or a joint as it expands, and a covering already thin at a worn edge is where that pressure is felt.
Ponding is the winter problem and the summer problem alike, but a pool that freezes stays longer than one that dries. BS 6229:2025 covers flat roofs with continuously supported flexible waterproof coverings, and NFRC reports that it sets a minimum 1:80 finished fall for general roof areas and internal gutters. Built to a proper fall, a roof drains in cold weather as it does in warm.
Do not chip ice from a membrane with a spade, a hammer or any hard tool, because a hard tool can cut or puncture the covering and turn a frozen roof into a leaking one. Do not pour hot water onto frozen outlets either, as it can refreeze lower down the pipe. Leaving the ice to thaw is slower and safer for the covering.
Look at where water sits once the thaw begins. A pool that forms in the same place each time suggests the deck dips there. The notes from the problems guide on ponding apply, and a roof that holds water through the winter is one for a survey in the spring, or sooner if there is a leak inside.
Condensation: the winter stain that is not a leak
In winter, the moist air from kitchens, bathrooms and living rooms rises to the ceiling and can pass into the roof build-up. If it meets a cold surface it turns to water, which can show as damp patches, dark spots or mould on the ceiling below. A stain showing up in the cold, which does not follow the rain, may be condensation, not a split.
BS 5250 deals with moisture in buildings. Marley's cold roof advice, where a high-resistance underlay is used, is eaves ventilation of 25 mm where the pitch is 15° or less, and 10 mm above 15°. Vapour does not pass through that underlay, so air has to be able to move through the roof space instead.
Whether a flat roof is warm or cold, meaning where its insulation sits relative to the deck, decides where condensation can form and what keeps it down. Our guide to warm and cold flat roofs sets out the two builds. A survey can tell whether a damp ceiling is condensation or a leak, and the two call for different work.
Patching a covering does nothing for condensation, and extra ventilation will not mend a split. Note when the stain appears, whether it follows rain, and whether the room below is a steamy one. Those notes help to separate the two causes.
After a storm: the steps to take
Rain, wind and snow can damage a flat roof in a single night. The Financial Ombudsman Service, which settles insurance complaints, gives its view of a storm: "a storm usually involves violent winds, usually with rain, hail or snow", while "Rain, hail or snowfall by itself can constitute a storm". Whether damage counts as storm damage is a question for the insurer under the policy.
The Financial Ombudsman Service says it will usually look at expert reports and photos, so photograph the damage before anything is moved. Photograph the roof from the ground if it cannot be reached safely, of the ceiling or wall inside, and of anything that has been damaged. Then tell the insurer. Keep any receipts for temporary work done to stop the water.
- photograph the damage before anything is moved
- stop more water coming in, from inside if that can be done safely
- tell the insurer, and keep the policy details to hand
- keep receipts for any temporary protection
- send the photographs on for a look at the roof
On insurer complaints, the Financial Ombudsman Service says: "For most complaints, a business has up to 8 weeks to consider a complaint". The Financial Ombudsman Service can be reached on 0800 023 4567. A roof that has been damaged and temporarily covered still needs its own assessment, covered by our guide on whether to repair or replace a flat roof.

