What the published figures say
Two sources give flat roof lifespans by covering: HomeBuilding, on a page last updated on 30 September 2025, and Less, on a cost guide whose page now reads last updated 12 November 2026. Neither gives the same figures as the other, so the table sets out both, each under its own name. Both list lead as a flat roof covering, while zinc and lead flashing, which come later, have their own sources.
| Covering | HomeBuilding | Less |
|---|---|---|
| Felt | 10-15 years | 10 to 20 years |
| GRP | 25-30 years | 25 to 40 years |
| EPDM | 25-30 years | 30 to 50 years |
| Lead | 60-100 years | 50 to 100 years |
HomeBuilding labels its column an approximate lifespan. Less attaches conditions to some of its lines, which the next section quotes. Each source's own words are kept because the figures are theirs and not ours, and neither is a promise about any individual roof.
Read across the table and the first thing to notice is how much the covering matters. Felt sits at the short end whichever source is used, and lead at the long end. In between, EPDM and GRP overlap, and the choice between them rests on more than how long each lasts.
Reading a lifespan with care
A lifespan is an estimate of how long a covering can be expected to keep water out. It is not a measured guarantee, and neither source offers it as one. The words each source chose are worth reading closely, since they carry the conditions.
Less writes that "EPDM rubber membrane typically lasts 30 to 50 years", that "GRP fibreglass lasts 25 to 40 years with minimal maintenance" and that "Torch-on felt lasts 10 to 20 years depending on quality and installation". It calls lead "the longest-lasting option at 50 to 100 years". Each phrase has a condition in it: minimal maintenance, quality and installation, or the word typically.
A figure for a covering assumes the covering was laid properly on a sound deck and has been looked after. A roof that was installed badly, or has been left with a blocked outlet for years, is outside what the figures describe. A roof can also pass its published age and carry on, or fail inside it, and what matters is the roof actually in front of you.
For that reason, a roof's age is a prompt to look at it and not a verdict. The questions to ask are what the covering is, the year it was laid, the care it has had and its condition now. The survey answers the last of those from the roof itself.
Felt: the short end
Built-up felt, and the torch-on form that is melted onto the layer beneath, has the shortest lifespans in both sources: 10-15 years from HomeBuilding and 10 to 20 years from Less, which adds that the figure depends on quality and installation. Less ties the figure to quality and installation, so a felt roof is not defined by its range alone.
A felt roof is built of layers. The number of layers, the grade of the felt and the workmanship at laps, upstands and edges all belong to the quality that Less refers to. Two felt roofs on neighbouring garages can therefore age at different speeds, which is the reason a published range is wide.
A felt roof close to the end of its working life may show cracks along the laps, a surface that has gone brittle, blisters that have split and seams that have opened. Our guide to flat roof problems shows what each of those looks like and what it can mean.
Felt is also where a repair is easiest to weigh against replacement, since a patch on a worn felt roof sits against a covering that may already be near its age range. A roof surveyed at that stage is judged on the roof as it is, not on its date alone.
EPDM and GRP side by side
EPDM is a rubber sheet laid over the deck and bonded at the edges and seams. GRP is glass-reinforced plastic, a resin and glass fibre layer formed in place on the roof. Both sources put them in the same bracket at the lower end of their figures: HomeBuilding gives 25-30 years for each, and Less gives 30 to 50 years for EPDM and 25 to 40 years for GRP.
Less gives the longer figure for EPDM, and HomeBuilding gives the same figure for both, so the two sources do not settle which lasts longer. What can be said is that both fall well above felt in each source, and that each has conditions attached: minimal maintenance for GRP in Less's wording, and correct installation for both.
A difference in how they fail matters more than a difference in their ranges. An EPDM sheet can fail at a seam or an upstand where the bond has lifted, and a GRP roof can crack where the deck moves under it. Each failure sits at a detail, which is why the edges and corners get as much attention at a survey as the open area.
Our guide to EPDM, GRP and felt sets the three coverings against one another in more detail.
Lead and zinc: the long lives
Lead sheet has the longest figures in the table: 60-100 years from HomeBuilding and, in Less's words, "the longest-lasting option at 50 to 100 years". The two ranges end at the same upper figure and start at different lower ones. BS 6229:2025 does not cover lead roofs, since it applies to flexible membranes.
On flashings, MyJobQuote says lead flashing that is correctly installed can last for over 80 years, and for higher codes the same page says over 100 years with minimal maintenance. That is a figure for correctly installed flashing, not for a lead roof, and it does not give a floor or a guarantee.
Rolled lead sheet comes in codes 3 to 8 under BS EN 12588, with code 4 at 1.80 mm. Under the specification each detail on the roof is given its own code, so thickness is another thing behind a lead roof's life. Where lead is dressed around upstands, the joints and fixings are the parts that move, so they are the parts a survey looks at.
Zinc is another long-lived option, and the figure comes from its maker, VMZinc: "When correctly designed and installed a zinc roof can last in excess of 100 years." It is a maker's statement, with the same two conditions as every figure here: the design and the installation have to be right.
What can shorten a flat roof's life
Several things can take years off a covering, and several of them are about water and movement rather than the age on the calendar. A roof that never drains well is at one end of the range, and one that sheds water cleanly is at the other.
- ponding, where water stands on the covering after rain
- blocked outlets and gutters that keep a roof wet
- movement in the deck that opens seams and laps
- damp in the boards, trapped under a new covering
- poorly finished upstands, flashings and edges
- foot traffic from people or from work done on the roof
BS 6229:2025 covers flat roofs with continuously supported flexible waterproof coverings, and NFRC reports that it sets a minimum 1:80 finished fall for general roof areas and internal gutters per the 2025 edition. Where the fall is right, less water stands on the covering, and that is one way a covering can reach the longer end of its range.
Maintenance appears in Less's own wording for GRP, "with minimal maintenance". Clearing leaves from an outlet and checking the roof after a storm are the kind of jobs that count. A roof that is looked at is a roof where a small fault gets found before it becomes a big one, and a short note of dates and photographs after each check shows how a covering is ageing.
When a roof's age means a survey
A roof inside its published range with no visible faults can be left alone and watched. A roof near the top of its range, or a roof with faults at its seams, is one to have looked at. A stain on a ceiling, a pool that stays or a bubble in the covering is reason enough at any age.
At a survey the covering gets looked at together with the deck under it, because a deck gone soft changes the answer. If the covering is worn out at the end of its working life while the deck is sound, replacement is a clean job. If the covering has only a local fault, a repair may be reasonable. Our guide on whether to repair or replace a flat roof goes through the choice.
Replacement brings in a Building Regulations point: Approved Document L puts the renewal of a flat roof's waterproof layer under renovation. Once more than 50% of the surface is renovated, para 11.3 expects an upgrade of the whole roof to Table 4.3 where feasible, with a 0.35 threshold and an improved 0.16 W/m²K.
To start, send a picture of the roof, with its covering and age if you know them, to 07880 284133 on WhatsApp, and we will give it a first look. We write the total after surveying the roof, and not before.

