Call 01582 935272

Flat roofing

What causes blisters on a flat roof?

A blister is a raised patch in a flat roof covering where something has been trapped beneath it. The causes, the risks of leaving a blister alone and the next steps all follow, in that order.

Get a written quote

Call 01582 935272WhatsApp us

A loft with spray foam removed
PicturedA loft with spray foam removed.

The short answer

Blisters on a flat roof can form when air or damp gets caught between the covering and the layer beneath it. Warmth then makes the trapped air or vapour expand and lift the surface. A blister can be a sign of damp in the roof, so it is worth watching and having looked at, but not worth bursting.

A roof drawing with its parts named: lantern, rubber deck, outlet, lead flashingLanternRubber deckOutletLead flashing

What a blister is

A blister is a bubble or raised patch in the waterproof covering of a flat roof. It appears where the covering has lost its grip on the layer below, and a pocket of air or moisture has taken the place of the bond. It may be the size of a coin or of a dinner plate, and it may be soft, firm or hollow when pressed.

The covering itself may still be watertight when a blister first appears. What matters is what lies beneath it. Trapped moisture can sit against the deck or insulation for months, and a surface that has lifted is more exposed to knocks, sun and foot traffic than one that is stuck down. A blister is therefore a prompt to find out why the bond failed.

Blisters can form in felt and other bonded or layered coverings, where the layers are stuck together by heat or adhesive. A covering that is loose-laid or mechanically fixed behaves differently, so what a raised patch means depends on the system on your roof. The guide to flat roof problems shows where blisters sit among the other faults.

How moisture and air get under the covering

Several routes can lead to a blister. Damp sealed in when the covering was laid, a poor bond, water getting in and vapour rising from inside are four of them. They are possibilities that a survey separates, since the same raised patch can come from more than one of them, and a single roof may show a mixture.

Ways a blister can form
RouteWhat happens beneath the covering
Damp laid overMoisture in the deck or old layers is sealed in
Poor bondAdhesive or heat did not take, leaving a gap
Water entryA split or open seam lets water in beside the blister
Vapour from insideWarm moist air rises into the roof and condenses

Sun then does its part. Warmth makes trapped air expand and water turn to vapour, and the covering lifts to make room. When the roof cools, the bubble may go down again, which is why a blister can seem to come and go. That does not mean the cause has gone, only that the covering has flexed.

Moist air from inside the house is covered in the warm and cold flat roof insulation guide, and it is one reason a roof's build-up matters as well as its covering.

What to do about a blister

Leave it unburst, however tempting it is to deflate it. Cutting or pricking a blister breaks the waterproof layer and lets rain into whatever has been trapped, and a hole made to release air can turn a small fault into a leak. Photograph it, note where it is, and look again after a few weeks to see whether it has grown or whether others have appeared nearby, since a spreading pattern says more than a single bubble.

Look inside as well. A damp patch on the ceiling below, a stain or a smell of damp can point to water that has found a way into the build-up. If there are none, the blister may be an early warning rather than a leak. Even so, the roof is worth having looked at before a winter, when trapped moisture can freeze and push the layers apart.

A blister can sometimes be cut out and patched, and a small isolated one may be repaired. A roof with many blisters, or with damp beneath them, may need more than patching, and the guide to repairing or replacing a flat roof goes through that decision. The flat roofing page sets out the options. Photographs on WhatsApp at 07880 284133 are a good start.

Flat roof blisters, answered

01Should I burst a blister on my flat roof?

No. A blister that is pricked or cut open lets rain into the layers beneath it, and the hole can start a leak where there was none. A raised patch is better photographed and watched, with the date and position noted. If you want it looked at, send the pictures to WhatsApp on 07880 284133, and the roof can be assessed before anything is cut.

02Does a blister mean my flat roof has failed?

Not necessarily. A single small blister on an otherwise sound roof is one thing, and a spread of them with damp inside the house is another. A blister shows that the covering has lost its bond in one place, so the question is why. Only a survey can say whether the roof can be patched or has reached the point where a new covering is the better route, and the written price follows it.

03Can a blistered flat roof be repaired without replacing it?

Sometimes. A small, isolated blister may be cut out, dried and patched, provided the layers beneath are dry and sound. Where many blisters have formed or the build-up is wet, patching can leave the cause in place, and the fault returns. Ring 01582 935272 to talk through what you can see, or send a photograph to WhatsApp on 07880 284133 so the roof can be assessed before a repair is chosen.

04Why does the blister on my roof shrink at night?

Trapped air and vapour expand in the warmth of the day and contract as the roof cools, so a blister can swell and then settle. The covering is flexing, not mending. A blister that shrinks overnight can still hide trapped moisture, and repeated movement can stress the surface until it splits, so it is worth having looked at before the next cold spell arrives.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote