Call 01582 935272

Guttering, soffits & fascias

What is a gutter outlet?

The outlet is the hole in the bottom of the gutter where water drops into the downpipe. The whole run is set to slope towards it, so it is the lowest point on the gutter.

Get a written quote

Call 01582 935272WhatsApp us

A gutter full of moss and debris below a tiled roof
PicturedA gutter full of moss and debris below a tiled roof.

The short answer

A gutter outlet is the opening in the base of the gutter where collected water drops into the downpipe. The run is laid to a slope of 1 mm for every 600 mm, Brett Martin says, so the outlet is its lowest point. Debris collects there, and a blocked outlet is one reason a gutter can overflow.

A roof drawing with its parts named: gutter, fascia, soffit, underlay, rafterGutterFasciaSoffitUnderlayRafter

Where the outlet sits and what it does

Look into a gutter from above and you will see a round or square opening in its base, with a short spout beneath it. That is the outlet. It is the single place where the water gathered along the roof edge is allowed to leave the channel. Beneath it sits the top of the downpipe, which carries the water on down the wall, so the outlet is the join between the two halves of the system.

An outlet can be at the end of a gutter run or part way along it. At the end of a run, the whole gutter slopes one way. Part way along, the gutter slopes down towards it from both ends, which suits a longer stretch, because each side has a shorter distance to carry water. The position is chosen when the gutters are laid out, and it decides where the downpipe has to go.

Brett Martin, a guttering manufacturer, says guttering "should be installed with a downward fall" towards the outlet, at 1 mm for every 600 mm. The outlet is therefore the lowest point on the run, and the fall exists to send water to it. The gutter fall answer shows what that slope looks like in practice.

Types of outlet and why they block

Outlets are made for each gutter profile, so a half-round gutter takes a half-round outlet and a square-line gutter a square-line one. A plain outlet is a straight drop. A stop-end outlet sits at the end of a run and closes it off as well. A running outlet sits in the middle of a run and lets water pass through from both sides. Which one is used depends on where the downpipe is and how the run is laid out.

  • Leaves and twigs washed along the gutter and caught at the opening.
  • Moss and silt, which build up where water slows near the outlet.
  • A toy ball, a bird's nest or other items that lodge in the opening.
  • A downpipe blocked below, which backs water up to the outlet.
  • A cracked outlet or a loose seal, which leaks around its edge.

The outlet is the narrowest point on the water's path, so it is also the easiest place for a blockage to take hold. Because the whole run slopes to it, anything the water carries ends up there. A gutter that spills in a downpour while the rest looks clear can be blocked at the outlet, and the gutter cleaning and winter guide covers keeping it open through the colder months.

When an outlet needs attention

Some warning marks point at the outlet itself. Water that stands near the opening instead of draining, a wet stain on the wall directly beneath it, green growth running down from it, or water that drips around its edge while the gutter is otherwise sound all suggest a blocked or leaking outlet. The signs your gutters need work guide lists more.

A blocked outlet is cleared by hand from above, and the downpipe beneath it is checked to see that water now flows freely. A cracked or loose outlet is swapped for a new one and resealed to the gutter. Where the slope has been lost, so that the outlet is no longer the lowest point, clearing alone will not hold, and the gutter needs to be reset towards the opening.

Reaching an outlet means a ladder or access equipment. A ladder should never rest on the gutter, which is not built to take the load. If the outlet is on a high or awkward stretch, the access is part of the job, and the survey leads to a single written total. For the wider picture, see the guttering, soffits and fascias hub.

Gutter outlets, explained in plain terms

01How many outlets does a gutter run need?

That depends on the length of the run, the area of roof feeding it and the layout of the house. A short run can drain to one outlet at its end. A longer run can drain to one in the middle, or to one at each end. No single number fits every house. If a gutter overflows at one end, it may be that the run has too few outlets for the water it takes.

02Why does the gutter overflow beside the outlet?

Water reaches the outlet from both sides in a rush, and if the opening is partly blocked, or the downpipe below is narrower than the flow, it backs up and spills at that spot. Debris is carried to the point where the whole run drains, so a clog can build up there. Clearing it, and checking the pipe below, is the first step before looking at anything else.

03Can an outlet be moved to a different place?

It can, but moving it changes the fall of the gutter, because the run has to slope to the new position, and it changes where the downpipe stands. A new position needs a drain or gully to receive the water. Before an outlet is moved, the whole run and the route of the pipe are considered together, and the price follows the survey.

04Is an outlet the same as a hopper?

No, though they sit close together. An outlet is the opening in the gutter. A hopper, sometimes called a rainwater head, is a funnel-shaped box set at the head of a downpipe. It receives water from the outlet and sometimes from other pipes, and is found on some older houses. A plastic system fitted today can have a plain outlet connected straight to the pipe.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote