Call 01582 935272

Lead roofing

Can lead flashing be repaired?

Yes, a faulty flashing can sometimes be mended without stripping the whole strip. The deciding point is whether the lead around the fault is still sound.

Get a written quote

Call 01582 935272WhatsApp us

A valley between two concrete tile slopes with a dry valley trough
PicturedA valley between two concrete tile slopes with a dry valley trough.

The short answer

Yes, lead flashing can be repaired when the metal around the fault is still sound. A split, a lifted edge, a slipped wedge or failed pointing can be put right on its own. Where the lead is worn, cracked along its length or pulling away from the wall, renewing the strip is the sounder route.

A roof drawing with its parts named: lead valley, tiles, hipLead valleyTilesHip

Faults a patch can settle

A flashing is a strip of lead that seals the junction between a roof covering and something that rises through or beside it, such as a chimney stack or a wall. It is held at the top by lead wedges and pointing set into a cut joint in the masonry, called a raggle, while its lower edge is dressed down over the tiles or slates. Because the strip is made of several fixed points, a fault in one of them does not always mean the whole strip has gone.

A repair can cover a small split in an otherwise good length, a hole where something has pierced the metal, an edge that has lifted away from the covering, wedges that have slipped or dropped out, and pointing that has crumbled so the top edge is no longer held in the joint. Each one is dealt with where it is. A new piece of lead is dressed in over a split, loose lengths are secured and the raggle is re-pointed.

A smear of black sealant across the same split is a different thing from a repair. It hides the gap for a while and leaves the weather a way in behind it. The comparison of lead and its alternatives goes into why a flashing is shaped to the junction and not filled in.

When a patch is not enough

The condition of the lead around the fault decides the outcome, not the size of the fault. A patch has to be fixed to the old metal, so it depends on that metal holding. If the old lead is thin, brittle or cracked in several places, a new piece can end up sitting next to a fresh failure.

  • Splits or cracks in more than one place along the same strip.
  • Lead that has worn thin, so a repair would have to be fixed to weak metal.
  • A flashing pulling away from the wall along much of its length, not just at one end.
  • Rot or soft boards under the lead, which a patch on the surface cannot reach.
  • Lead that has been repaired before, so the old patches are failing around the new one.

In those cases renewing the strip is the more dependable route. New lead is cut to the length needed, dressed to the wall and the covering, wedged and pointed, and the code of lead comes from the job's specification. The repair or replace lead flashing guide walks through the same decision part by part.

Cost, lifespan and what to ask

Third-party figures give a sense of scale. MyJobQuote, on a page updated 22 September 2026, gives a chimney lead flashing patch as typically costing around £200, with a full replacement averaging around £570. Both numbers cover chimney leadwork alone, so they are not a guide for a valley, a bay roof or a long wall abutment, and they are not a price from us.

On lifespan, MyJobQuote also says correctly installed lead flashing can last for over 80 years. That is a figure for lead that is installed well and left undisturbed; it does not mean a particular flashing on a particular roof is sound today. That judgement is made by looking at it.

What we quote after the survey is a single written sum covering the job. A repair is treated no differently, and a small patch is priced on the same footing as a longer renewal. When weighing a patch against a new strip, ask what is being fixed, which lengths are being renewed and what lies beneath the lead. A clear photo of the fault sent to 07880 284133 on WhatsApp is a good place to begin. The lead roofing page lists the other leadwork details a survey covers.

Repairing flashing, asked directly

01Will one patch hold for good?

It can, if the metal around it is sound and the cause of the split has gone. Sheet lead swells in warm weather and shrinks in cold, and a split can open again if the strip was cut too long or pinned too firmly to move. A patch that treats the symptom but leaves that cause alone may need doing twice, so it is worth raising at the survey.

02How do I tell a tired flashing from a failed one?

Look from the ground, or through binoculars from the garden. Pale, powdery lead is ordinary weathering and is no fault. Cracks, gaps along the top edge, a lifted corner and tide-marks down the wall below are the signs to note. Indoors, a damp patch beside the chimney breast after rain points the same way. Photograph what you see before anything is touched, and keep the pictures with the date. They are useful at a survey and, if the damage followed a storm, for an insurer.

03Can I mend a flashing myself from a ladder?

Climbing up is not worth the risk. A chimney stack or a wall junction means leaning out from a ladder with tools in hand, and the repair itself needs lead shaped properly to the detail. A temporary smear from a tube also complicates the proper repair, since the surface then has to be scraped clean first. Photograph the fault and ask for a survey instead.

04Does a repair have to match the old lead?

The new lead is cut from rolled sheet made to BS EN 12588, which comes in codes 3 to 8. Code 4, for example, is 1.80 mm thick. The specification gives every lead detail its own code, so a patch is chosen to suit its own detail, not copied from whatever was there before. If the old lead was a lighter code than the detail calls for, that comes out at the survey.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote