Call 01582 935272

Lead roofing

What are drips and rolls on lead sheet?

Lead sheet on a flat or low-pitched roof is laid in strips called bays. Drips and rolls are the two ways those bays are joined, one down the fall and one beside it.

Get a written quote

Call 01582 935272WhatsApp us

A freshly repointed brick chimney with new lead flashing and flaunching on a clay tile roof
PicturedA freshly repointed brick chimney with new lead flashing and flaunching on a clay tile roof.

The short answer

Drips and rolls are the joints between lead sheets on a roof. A drip is a step formed in the deck that lets one bay of lead overlap the next down the fall of the roof, so water drops over the joint. A roll is a timber batten wrapped in lead, set between two bays that lie next to each other.

A roof drawing with its parts named: lead valley, tiles, hipLead valleyTilesHip

Why lead sheet needs joints at all

Lead is rolled into sheets, and a roof or a bay window top can be bigger than one sheet. The surface is therefore built up from bays, which are strips of lead laid down the fall of the roof. Where one strip stops and the next begins, a joint has to keep water out while letting the metal move. Temperature makes lead grow and contract, and a long unbroken sheet would be tugged by that movement until it cracked.

Two kinds of joint do the job. Which one is used depends on the direction in which the joint runs. A joint across the fall, where one bay ends and the next starts lower down, is a drip. A joint along the fall, between two neighbouring bays, is a roll. Both are formed by the roofer on site, from the sheet and from timber, and both are laid out when the roof is planned.

These details belong to lead laid as a sheet covering, as on a bay window, a porch or a small flat roof. Flashings that run up a wall or round a chimney are a different set of details, described on the lead roofing page.

How a drip and a roll are built

A drip is a step. The roof deck is formed with a small drop at the joint, and the upper bay of lead is dressed over the edge and down the face of the step, where it overlaps the lower bay. Water running down the fall reaches the step and falls onto the lower sheet, and it cannot creep sideways or uphill back under the joint. The height of the step is part of the design, and the lead has to be long enough to cover it.

A roll is a rounded wooden batten fixed down the deck along the fall. The lead from one bay is dressed up and over it, and the lead from the next bay is dressed over that, so one sheet laps the other across the top. The batten lifts the joint above the line where water runs, which keeps rain from being driven sideways between the sheets.

  • Drip: runs across the width of the roof and joins bays one below another.
  • Roll: runs down the fall of the roof and joins bays side by side.
  • Both rely on the shape of the lead and not on sealant.
  • Both leave room for the metal to expand and contract.

Where they show and what goes wrong

On a bay window or a porch top, drips and rolls show up from a bedroom window or from a ladder. A roll looks like a raised ridge of lead, and a drip looks like a small step in the surface. On a flat roof, they are the lines that divide it into strips.

Faults can start at these joints because they are where the metal works hardest. A lifted edge, a crack along the top of a roll, a wrinkle or a split at the corner of a drip can each let water through. The signs of failed leadwork guide lists what to look for, and the lead bay and porch roofs guide covers how those roofs are built.

BS 6229:2025 deals with flat roofs that use continuously supported flexible waterproof coverings, which means membranes and not lead, so a lead roof follows its own detailing. Thickness is named in the job's specification, since lead sheet to BS EN 12588 comes in codes 3 to 8 and code 4 measures 1.80 mm. A price follows a survey as a single written sum, and a clear photograph of the roof sent to 07880 284133 on WhatsApp gives us something to look at first.

Drips and rolls, explained simply

01What is the difference between a drip and a roll?

They are joints that run in different directions. A drip runs across the roof and is a step where one bay of lead ends and the next begins lower down the fall. A roll runs along the fall and is a wood-cored ridge between two bays side by side. Between them, they let a large roof be covered in sheets without leaving open seams.

02Why does lead split at a drip?

Because the metal moves there. Lead expands when it warms and shrinks as it cools, and a sharp fold at the top of a step is where that movement concentrates. If the lead was cut too long, dressed too tight or worn thin, the fold can crack with repeated cycles. A split at a drip points to a cause that should be found before the patch is made.

03Do pitched roofs have drips and rolls?

Not in the same way. Drips and rolls belong to lead laid as a sheet covering on a flat or gently sloping surface, such as a bay roof, a porch or a small flat roof. A pitched roof of tiles or slates carries lead in other forms, such as flashings, valleys and soakers, which are made differently and sit under or over the covering.

04Can a damaged roll be repaired?

It can, if the lead and the timber under it are sound. A split can be patched with a new piece, and a lifted edge can be re-dressed. If the batten has rotted or the lead has worn through along the roll, the roll is rebuilt, which means lifting the sheet beside it. The survey looks at the roll, the lead and the deck together.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote