Call 01582 935272

Pitched roofing

What is the minimum pitch for roof tiles?

No single pitch suits every tile, because each product has its own minimum angle. The lists below give Marley's figures, and the pitched roofing page covers how a roof is re-covered.

Get a written quote

Call 01582 935272WhatsApp us

Hip tiles torn loose by wind on a bungalow roof
PicturedHip tiles torn loose by wind on a bungalow roof.

The short answer

There is no one minimum, because it depends on the product. Marley lists 40° for its clay Canterbury tile, 35° for Ashdowne and for its plain concrete tile, and 15° for its Lincoln clay pantile, with other concrete tiles from 12.5° upward. The roof's specification decides which figure applies.

A roof drawing with its parts named: ridge, even courses, verge, eavesRidgeEven coursesVergeEaves

What pitch means for a tile

Pitch is how steeply a roof slope climbs, measured in degrees against the horizontal. A steep roof sheds rain quickly, and a shallow one lets water run slowly across the tiles. Because tiles overlap rather than seal, a slope that is too shallow can let rain creep upward under the laps, particularly when wind pushes against it.

Each tile design copes with that problem differently. A deep lap and a steep slope work together on a plain tile, while a tile with a side interlock and a profile that channels water can sit at a lower angle. That is why manufacturers publish a minimum pitch product by product, and why one rule for all tiles would be wrong.

The angle is read off the roof itself, from a drawing or a measurement, and not guessed from the ground. A roof that looks flat from the street can still be a pitched one, and the roof over an extension can sit at another angle from the main house.

The minimum is also not a target. A tile laid right at its minimum has no margin, so a designer weighs the figure against how exposed the roof is and what else the roof must do.

Marley's list, product by product

These are the figures Marley publishes as minimum pitches. Some of the labels sound like places, yet each one is a tile and none has a connection with any town.

Marley clay tiles, minimum pitch
Clay productMinimum pitch
Canterbury40°
Ashdowne35°
Hawkins30°
Acme Single Camber30°
Lincoln pantile15°
Marley concrete tiles, minimum pitch
Concrete productMinimum pitch
Plain35°
Edgemere, Modern-Duo17.5°
Double Roman22.5°
Mendip15°
Mendip 12.512.5°
Ludlow Major, Ludlow Plus22.5°
Wessex15°
Anglia25°
Ashmore22.5°

Put the lists side by side and a pattern shows. The clay tiles run from 15° for the Lincoln pantile up to 40° for Canterbury, a spread of 25 degrees between two clay products. The concrete tiles run from 12.5° for Mendip 12.5 up to 35° for the plain tile. Low figures suit shallow slopes, and high ones call for steeper roofs. The two plain-tile figures, Ashdowne in clay and Plain in concrete, are both 35°.

Read the tables as manufacturer figures. They describe Marley's products and not tiles in general, and another maker's tile has its own published minimum. The clay and concrete tile comparison covers other points that decide a choice.

Slate, the specification and a shallow roof

Natural slate has its own figures. Cupa reports that BS 5534 "also indicates that the minimum roof pitch for natural slate is 20 degrees in the case of a project situated in an area with moderate exposure and with a slate 500mm long and a 115mm overlap". Hook fixings, Cupa adds, are not for any pitch below 25º. Slate length, lap and exposure all feed into that figure.

The specification for the roof has the last word. A tile's published minimum is a starting point, and the exposure of the site, the length of the slope and the way the tile is fixed all feed into whether it suits the roof. The standard for the covering is BS 5534, which BSI lists as current in its 2014+A2:2018 edition.

A roof below the figure for a chosen tile has three choices: a tile with a lower minimum, a different type of covering, or a change to the roof's pitch, which is a structural job. A survey measures the actual angle before any of those is weighed, and the written quote then covers whichever route is picked.

Pitch also affects the loft. Marley's ventilation figures turn on the 15° mark: 25 mm of eaves ventilation at 15° or less and 10 mm above it, for a cold roof under an HR (high resistance) underlay. The pitched roof ventilation guide covers the details.

Roof pitch, question by question

01Can I use a tile on a roof below its minimum pitch?

Not on the strength of the published figure. A tile's minimum is the angle the maker states for the product, and going below it risks water getting under the laps. A designer can choose a tile with a lower minimum, or a different covering, and the roof's specification records which one is used, so the choice is made on paper before any tile is ordered.

02How do I find out my roof's pitch?

A drawing may state it, and a survey can measure it from the gable or the slope. A phone app can give a rough angle, but a rough figure is not enough where a tile sits close to its minimum. If you are choosing a covering, tell the surveyor the tile you have in mind so the angle is checked against it.

03Is Canterbury or Anglia a type of roof?

No. They are Marley product names, a clay tile and a concrete tile. Canterbury is listed at 40° and Anglia at 25° as minimum pitches. The names were chosen by the maker and say nothing about where a tile can be used, so the pitch figure, and not the name, is what matters on a roof. Neither is a place you can visit.

04Does slate need a different minimum pitch from tiles?

It does. Cupa's reading of BS 5534 gives 20 degrees for natural slate, subject to moderate exposure and to the slate's length and overlap, and its hook fixings are not for pitches below 25 degrees. A change in slate size, lap or exposure shifts the answer, so the specification for the roof settles it for good. Ask for the slate's size to be named on the specification.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote