Call 01582 935272

Slate roofing

How is a valley made on a slate roof?

Where two slopes of a slate roof meet at an inward angle, the water from both runs into one channel. How that channel is built decides whether the join stays dry.

Get a written quote

Call 01582 935272WhatsApp us

Lead flashing and soakers around a chimney on a clay tile roof
PicturedLead flashing and soakers around a chimney on a clay tile roof.

The short answer

A slate valley is the inward angle where two roof slopes meet. It is built from a metal lining, such as lead, laid in the angle, with slates cut to follow it on each side. Rain from both slopes runs down that lining and off the roof, so the lining and the cut edges carry the join.

A roof drawing with its parts named: slates, slipped slate, tingle, battensSlatesSlipped slateTingleBattens

What a valley does on a slate roof

Roofs are not always one flat plane. An L-shaped house, a bay with its own roof, or a rear extension meeting the main slope all create an inside corner where one slope runs into another. That corner is the valley. It collects the rain from two slopes and carries it down to the gutter, so it has to cope with more water than a single stretch of roof does.

The slates on each side cannot simply be butted together in that corner. They are cut along a diagonal line to follow the angle, and a lining sits underneath to take the water that runs between them. The slates hold the weather off the sides of the lining, while the lining forms the actual channel. If either part is poorly made, water gets under the slates and onto the timbers below.

A valley is therefore one of the details on a slate roof that is made by hand for each house. No two corners are the same length, angle or width, which is why the cut slates and the lining are measured and shaped on the roof instead of being supplied as a ready-made part. The wider slate roofing page covers how the whole covering fits together.

How the lining and the slates are put together

The starting point is a continuous lining laid in the angle over the battens and underlay, extending well up each slope so that water has to travel a long way sideways before it could reach a joint. Lead is one lining material. Rolled lead sheet is made to BS EN 12588 in codes 3 to 8; code 4, for example, is 1.80 mm thick, and the specification sets the code for each detail. Other metals can also be used, and some valleys are formed with a purpose-made profile instead.

Once the lining is in place, the slates on each side are cut along the line of the angle. They are fixed so that their cut edges stop short of the centre of the channel and leave a clear gap, with enough lining showing to carry the water. The width of that gap is a design choice. A very narrow one can block with leaves and moss, while a very wide one exposes more metal.

  • Lining laid over the underlay and fixed along its upper edges, so that it can move slightly as it warms and cools.
  • Slates cut to a clean line, with the cut edge bedded on the lining and not on a bed of mortar.
  • Fixings placed so that no nail passes through the open channel.
  • The channel kept clear along its length so water runs freely to the gutter.

A valley made of slate and lead is part of the roof's design and not an add-on, so its detail is decided with the pitch of both slopes in mind, as discussed in the minimum pitch for slate.

Signs a valley is failing

A valley is hard to see from the ground, because it sits in a fold of the roof. The signs can show up inside the house first, as a damp patch on a ceiling or an upper wall beneath the line of the valley. A stain that runs diagonally across a ceiling is worth looking at, since it can point to a corner on the roof above.

From outside, a few things can be spotted from the ground with binoculars, or by looking at a clear photo taken from a window or ladder-free vantage point.

  • Moss, leaves or debris piled in the channel, which can hold water against the slate edges.
  • Slates beside the valley that have slipped or cracked, leaving a gap over the lining.
  • Lining metal that has cracked at a fold, curled at an edge or worn thin.
  • Light showing through at the cut edge of a slate when seen from the loft.

None of these proves a leak, and a damp patch can have other causes, such as a gutter overflow or a failed flashing at a chimney. The point of a survey is to trace where the water enters. A failed valley can sometimes be dealt with as a repair to the lining and the nearby slates, while a lining that has worn out along its whole length may need replacing with the slates lifted and relaid. How to weigh that choice is set out in repair or replace a slate roof.

Slate valleys, answered in turn

01Is a slate valley the same thing as a flashing?

They do related jobs but are different details. A flashing is a strip of metal that seals the join between a roof and something that rises above it, such as a wall or a chimney. A valley is the channel where two slopes meet, and its lining carries water along it. Lead is used for both, which is why the two are sometimes confused.

02Can a slate valley be lined with something other than lead?

Yes. Lead is one choice, and other metals and purpose-made valley profiles can also be used. The right material depends on the pitch, the width of the channel and how the roof is built, so the choice is made for each roof once it has been surveyed. The written quote then gives one total price for the work, with the lining as part of it.

03Why does a valley leak when the slates beside it look fine?

The visible slates only shelter the sides of the channel. The water travels along the lining beneath them, so a crack, a curled edge or a blocked channel can send water under slates that look sound from the ground. A leak can also start where a slate has been cut too short, or where a nail was driven through the open channel.

04What do I do if my valley may be leaking?

Check the ceiling and loft timbers beneath it after a spell of rain, and photograph any staining, noting where it falls along the roofline. Then send the pictures on WhatsApp to 07880 284133, or call 01582 935272, and ask for a survey. Stay off the slates yourself, because they crack underfoot and a valley is a slippery place to stand.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote