Call 01582 935272

Flat roofs, Part L

Replacing a flat roof: the Part L upgrade explained

Where a flat roof is given a new waterproof layer, Part L treats it as renovated, and that can mean bringing the insulation up to a set standard at the same time. The figures, the tests and who checks the work in Bedfordshire, Hertfordshire and Milton Keynes follow.

21 September 2026 10 minute read

Get a written quote

Call 01582 935272WhatsApp us

Rear flat roofs of a brick shop parade with flats above
PicturedRear flat roofs of a brick shop parade with flats above.
A roof drawing with its parts named: lantern, rubber deck, outlet, lead flashingLanternRubber deckOutletLead flashing

Why a new membrane brings in Part L

A flat roof replacement is two jobs in one. The waterproof layer comes off and a new one goes on, and the energy rules in Approved Document L, volume 1, 2021 edition, look at what that does to the roof as a whole. The document lists renovation work, and one of its entries is "Replacing the waterproof membrane on a flat roof." So a re-covered flat roof is not outside Part L, even when nothing about the room below changes.

The test is the size of the work. Paragraph 11.3 draws its line at 50%. Past that share of an individual thermal element's surface, the work counts as renovating the element, and the new figures apply to all of it where that is feasible. A thermal element, in the Building Regulations 2010, "means a wall, floor or roof (but does not include windows, doors, roof windows or roof-lights)". A flat roof is one element, so a replacement over all of it, or over more than half, is inside the paragraph. A repair patch on a small area is not.

In plain terms, the first question a customer should expect to hear is how much of the roof surface is coming off. A full replacement answers it. A partial one needs the area measured, because a few square metres on a large roof and most of a small garage roof sit on opposite sides of the line.

The Planning Portal reaches the same door by a second route: it says "In most situations, this work will need Building Regulations approval." A full re-covering also affects more than 50% of the roof, which is past the limit in the Portal's own test.

The 0.35 and 0.16 figures

Table 4.3 of the approved document is the one for a roof that is being renovated. It carries two numbers for a roof, a threshold of 0.35 and an improved figure of 0.16, both in W/m²K. The U-value is a measure of the heat that passes through a construction, so a lower figure means less heat lost.

The way the two numbers work together is easy to misread. An existing roof that is retained and sits above the 0.35 threshold is upgraded to reach the improved 0.16. A renovated roof is therefore judged against Table 4.3, not against the figure for new fabric. The new-fabric table, Table 4.2, lists 0.15 for a roof built new, such as the roof of a new extension, and that is the number the renovation table should not be confused with.

Part L 2021 roof U-values in W/m²K
CaseTableFigure
Existing roof, threshold4.30.35
Existing roof, improved4.30.16
Roof of a new extension4.20.15

A third number sits in the background. The document says "Generally, a thermal element once upgraded should not have a U-value greater than 0.7W/(m2·K)." That is a ceiling for the case where the full figure cannot be reached, and it is a different thing from the target.

The figures describe the whole build-up, from the deck to the covering, and not the membrane alone. A new membrane laid on an uninsulated deck does not move the figure.

Feasible, and the 15-year payback

The improved figure is not demanded by Part L at any cost. Paragraph 4.13 covers the case where reaching it "is not technically or functionally feasible or" would not achieve a simple payback of 15 years or less. The upgrade then settles on the lowest feasible U-value, provided it "can achieve a simple payback not exceeding 15 years."

Simple payback sets the cost of the extra insulation against the energy it saves. The approved document does not fix a thickness. The answer therefore depends on the roof: its construction, what sits above and below it, and how much space there is to add insulation without causing a fault elsewhere, such as a door threshold that ends up too low or a parapet that becomes too short.

  • Is more than 50% of the surface being renovated?
  • What is the present U-value of the roof, if it is known?
  • Can the improved figure be reached without a fault elsewhere?
  • If not, what is the lowest figure that is feasible and pays back within 15 years?

Those four questions are the ones building control puts, and an owner is better placed when they are answered before the work is priced. The page on flat roof building regulations covers the same ground from the regulation side.

The edition matters too. Approved Document L 2026 applies from 24 March 2027, with its tables renumbered 3.2 and 3.3. Until that date the 2021 tables above are the ones in use for work in England.

Warm roof or cold roof, and the finished fall

Where the insulation sits decides much of the job. A warm roof puts the insulation above the deck, directly beneath the waterproof layer, so the deck and the structure stay on the warm side. A cold roof has its insulation between or below the joists, with ventilation in the space above it. A replacement can keep the existing arrangement or change it, and the choice is made on the roof, with the surveyor looking at it.

The roof also has to drain. BS 6229:2025 now stands as the code of practice for flat roofs with continuously supported flexible waterproof coverings, and it replaced the 2018 edition, which is withdrawn. NFRC reports that it sets "a minimum 1:80 finished fall for general roof areas and internal gutters". IKO reports that reaching 1:80 means designing the roof to a fall of 1:40.

Fall across a roof 3 m deep that drains to one side
FallDrop across 3 m
1:80, the minimum finished fall37.5 mm
1:40, the design fall IKO reports75 mm

The arithmetic is simple. A fall of 1:80 is one metre of drop over 80 metres, about 12.5 mm over a metre. New insulation laid in tapers can build the fall in, which is one reason a replacement is a chance to correct a roof that has been holding water.

BS 6229:2025 covers membranes. It does not cover lead, which has its own specification, and a flat roof of lead, zinc or another metal is a different system. For the two builds side by side, see the page on warm and cold flat roofs.

Rooflights and roof windows in a flat roof

A flat roof can carry a glazed unit, and Part L treats the two kinds differently. The definitions at the back of the document give this for a rooflight: "A glazed unit installed out of plane with the surface of the roof on a kerb or upstand". Its counterpart, the roof window, is "A window installed in the same orientation as, and in plane with, the surrounding roof". On that definition a lantern, or a skylight sitting on a kerb over a flat roof, is a rooflight.

The two sets of figures sit in Table 4.2. For a replacement roof window the table sets a minimum of Window Energy Rating Band B, or 1.4 W/m²K, and for a rooflight it gives 2.2 W/m²K. A quote that says "skylight" should say which of the two it means, because the words carry different figures.

Glazed units in Part L 2021, Table 4.2
UnitHow it sitsFigure
RooflightOn a kerb or upstand2.2 W/m²K
Roof windowIn plane with the roof1.4 or Band B minimum

Both are left out of the thermal element definition above, so a glazed unit is judged on its own row and not on the roof's U-value. A renovated flat roof may keep an existing rooflight, replace it, or have new ones added, and each of those has its own answer from building control.

A solid roof over a conservatory is a separate case. The Planning Portal says "A new roof must comply with building regulations", and the route is first put to building control.

Building control by council, and the certificate

Building control is carried out by the council's building control team or by a registered building control approver. Only the registration regime is new, from 6 April 2024. The council's team gives a completion certificate at the end, while an approver gives a final certificate, so the paper later tells a buyer which route was used.

Who the council team is depends on the postcode. The table covers the three unitary councils in this post.

Building control by council
CouncilProvider and number
Central BedfordshireIts own team, 0300 300 8635 (not for planning)
LutonIts own service, 01582 546607
Milton KeynesIts own team, 01908 252721 in office hours

In East Herts, building control comes from Hertfordshire Building Control Ltd, which East Herts Council owns jointly with other Hertfordshire local authorities (operations team 01438 879990). In North Herts it is Hertfordshire Building Control Ltd, owned jointly by North Herts Council with other Hertfordshire local authorities. Stevenage and Hertsmere are in the same position, and each uses Hertfordshire Building Control Ltd as well.

St Albans and Watford councils run a shared building control service of their own. For Dacorum, Three Rivers, Welwyn Hatfield and Broxbourne, check with that council's building control team. Luton's 01582 546607 is its building control service, and the council's main switchboard is a different line.

Lifespans, VAT on insulation and the written price

Two published sources give lifespans for flat roof materials, and they do not match. HomeBuilding, last updated 30 September 2025, gives EPDM 25-30 years, GRP 25-30 years, felt 10-15 years and lead 60-100 years. Less, last updated 12 November 2026, says EPDM "typically lasts 30 to 50 years", GRP "lasts 25 to 40 years with minimal maintenance", torch-on felt "lasts 10 to 20 years depending on quality and installation" and lead lasts 50 to 100 years.

Flat roof lifespans as two sources give them
CoveringHomeBuildingLess
EPDM25-30 years30 to 50 years
GRP25-30 years25 to 40 years
Felt10-15 years10 to 20 years
Lead60-100 years50 to 100 years

MyJobQuote's page of 20 October 2026 says "In 2026, the average flat roof replacement costs between £1,500 and £6,000." That is a national average from a third party and not a price for a particular roof. The roof is surveyed first, and you are given one written total afterwards.

HMRC's Notice 708/6 treats installing energy-saving materials, with insulation for "roofs or lofts" on its list, as zero-rated for supplies "made between 1 May 2023 and 31 March 2027", and the reduced rate of 5% applies after that. Whether a given job qualifies is a question for HMRC or the customer's accountant.

Replacing a flat roof also raises planning questions, and the guide on planning permission for roof work covers them. The flat roofing hub and the comparison of EPDM, GRP and felt cover the coverings. Photos of the roof can go to WhatsApp 07880 284133 for a first look from us.

Questions and answers

01Does replacing a flat roof membrane count as renovation under Part L?

Yes. Approved Document L lists "Replacing the waterproof membrane on a flat roof" as renovation. A renovation that reaches past half of the roof surface brings the whole roof under the upgraded figures, where feasible. A small repair patch is not in the same category, so the area being renewed is what building control will ask for, and it helps to measure the roof before the question is put.

02What U-value does a renovated flat roof have to reach?

Table 4.3 gives a threshold of 0.35 and an improved figure of 0.16, in W/m²K. A retained roof above 0.35 is taken to 0.16 when that can be done. If 0.16 cannot be done, or would fail the test of a simple payback of 15 years or less, the upgrade stops at the lowest U-value that can be done within that payback, which is a roof-by-roof judgement.

03Is a lantern on a flat roof a rooflight or a roof window?

A rooflight. Approved Document L describes a rooflight as sitting "out of plane with the surface of the roof on a kerb or upstand". A roof window sits "in the same orientation as, and in plane with, the surrounding roof". The first carries 2.2 W/m²K in Table 4.2 and the second 1.4 or WER Band B as a minimum, so the word used in a quote matters.

04Who signs off a flat roof once the work is finished?

That depends on the route taken. Where the council's own building control team did the checks, it gives a completion certificate. A registered approver gives what is called a final certificate. A later buyer who asks whether the roof was signed off needs whichever applies, and it is worth keeping with the title deeds, the survey reports and any invoice for the work.

05Do the 2026 Part L tables apply to a flat roof today?

No. The 2026 edition takes over from 24 March 2027, and its tables are renumbered 3.2 and 3.3. Work in England until then is judged on the 2021 edition, with Table 4.2 for new fabric and Table 4.3 for existing elements. A job that starts before that date keeps to the 2021 figures described on this page, and a customer can ask building control which edition it is applying.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote