Call 01582 935272

Commercial roofing

What is a composite insulated roof panel?

A composite roof panel arrives as one finished unit: two metal skins bonded to an insulating core. That makes it a different job from a sheet-and-liner roof, and it is surveyed differently.

Get a written quote

Call 01582 935272WhatsApp us

A high view looking down on a clay tile roof, its ridge, hips and brick chimney
PicturedA high view looking down on a clay tile roof, its ridge, hips and brick chimney.

The short answer

A composite insulated roof panel is a factory-made sandwich: an outer metal skin, a core of insulation and an inner metal skin, bonded into one unit. The panels span between purlins and are fixed through the outer skin, so the building gets its weatherproof covering and its insulation from a single layer in one fix.

A roof drawing with its parts named: rooflights, roller shutter, gutterRooflightsRoller shutterGutter

What sits inside the sandwich

A composite panel is made in a factory as a sandwich. The outer skin is profiled metal that sheds the rain. The inner skin faces into the building. Between them sits a core of insulation, bonded to both skins so that the three layers behave as one unit. Because the core is bonded, the panel is stiffer than the skins would be alone, and it can span the gap between purlins without a separate liner tray or a loose insulation quilt.

Core materials vary by product. Polyisocyanurate foam and mineral wool are both made into panels, and the choice may follow the building's use, its insulation target or its fire strategy. The maker's data sheet records the core, the thickness and the profile, so the first question about an unmarked panel on an older building is which product it is, because a repair or a replacement has to match it.

Panels are sold for roofs and for walls, and a wall panel cannot simply be laid on a slope. A roof panel has raised ribs that carry water down the slope and a fixing arrangement meant for a pitch. The pitch matters to the detailing: a low-pitched panel roof relies on sealed laps to keep water out, while a steeper slope drains faster and puts less weight on those seals. The skins can be coated steel or aluminium, and the coating is the layer that decides how the outer face ages under sun, rain and frost.

How panels are fixed and joined

Each panel is lifted onto the purlins and fixed through the outer skin with screws that carry sealing washers. Fixings are calculated for the site's exposure under a site-specific fixing specification, so the spacing on one building is not copied from another. The side of each panel overlaps the next one, and a bead of sealant sits in that lap. At the ridge, the eaves and the gable, trim pieces and flashings close the edges.

Joints are where a panel roof can let water in. A lap that was not sealed fully, a washer that has hardened, or a screw that was driven at an angle can each leave a path. The panel itself is a solid insulated unit, so a leak shows as a stain on the inner skin or on the ceiling below long after the water entered, which makes the entry point harder to place than the stain suggests. Thermal movement adds to the strain: a long metal sheet grows in warm weather and shrinks in cold, and the fixings and laps have to tolerate that movement for as long as the roof is in service.

Composite panel and sheet-and-liner roof compared
FeatureComposite panelSheet and liner
LayersBonded in the factoryAssembled on the roof
InsulationCore inside the panelQuilt between the layers
JointsSealed side lapsLaps in two separate layers
Spot repairPatch or panel swapSheet or liner swap

Where a panel roof shows its age

Reading a panel roof starts with the outer skin for dents, split coating and corrosion at the cut edges, which the cut-edge corrosion page describes. It looks at the laps and the sealant, the fixings and their washers, the rooflight panels, the gutters and the flashings at walls and ridges. Where a panel has been holed, water can get into the core, and a wet core may no longer insulate as it was designed to.

The choice between patching and replacing hangs on how far the damage runs. A single damaged panel can sometimes be swapped, while widespread coating failure may point to a new covering, a decision set out on the repair or replace page. On an older building a second question arises about what lies beneath the panels: HSE advises assuming that there is asbestos in any building built or refurbished before 2000, and AC roofs are always fragile.

A panel roof is priced after the survey, as one written total for the roof. The wider picture sits in the commercial roofing section, which covers the other coverings a business roof can carry.

Composite panels, answered one by one

01Is a composite panel the same as a built-up metal roof?

No. A built-up metal roof is assembled in layers on site: an outer sheet, a layer of insulation and an inner liner. A composite panel is bonded in the factory, so the insulation is part of the panel. The two can look similar from the ground, and the survey tells them apart by the edge of a panel and the way the laps are made.

02Can one damaged panel be replaced on its own?

It can be possible where the neighbouring panels are sound and the same product can still be supplied. The panel profile, the core thickness and the fixing pattern all have to match. If the surrounding skins are failing as well, replacing one panel may only move the problem along, which is why the extent of the damage is read first.

03Does a wet core matter?

It can. Insulation that has taken in water may stop working as intended, and the panel can corrode from within. Water can also travel along the core from the point of entry, so a stain on the inner skin may sit some way from the hole. Tracing the water back to where it entered matters more than treating the stain.

04What if the building is older than 2000?

HSE's wording is: "If the building was built or refurbished before 2000, assume that there is asbestos in it." A composite panel is not itself an asbestos product, but an older building may carry asbestos in other parts of the roof, so that question is settled before any work starts. A photo of the roof can go to 07880 284133 on WhatsApp as a first step.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote