Call 01582 935272

Commercial roofing

What is a standing seam metal roof?

A standing seam roof is made of long metal trays whose edges stand up and fold together. The fixings sit under the seam, so the weather-facing surface carries no screw heads.

Get a written quote

Call 01582 935272WhatsApp us

Roof lantern on a single-storey brick kitchen extension
PicturedRoof lantern on a single-storey brick kitchen extension.

The short answer

A standing seam metal roof is a covering of long metal trays whose edges are turned up and folded together into raised seams. Clips hidden inside the seams hold the trays to the deck, so no fixing pierces the surface. The seams stand proud of the roof and let water run past them down the slope.

A roof drawing with its parts named: rooflights, roller shutter, gutterRooflightsRoller shutterGutter

How the seams are made

A standing seam roof is laid in trays that run the full length of the slope, ridge to gutter. Each tray has an upturned edge on both sides. The edge of one tray sits against the edge of its neighbour, and the two are folded over together, by hand or with a seaming machine, into a raised seam that stands a short way above the roof. Water runs down the flat of the tray and never has to cross a joint on its way to the gutter.

The trays are held down by clips. Each clip is screwed to the deck and then locked into the seam as it is folded, so the clip is hidden when the roof is finished. Because the fixing is concealed, the surface carries no screw heads and no washers to harden. The clips are also built to let the tray slide a little, which matters because metal expands in the warmth and contracts in the cold, and a long tray moves further than a short one.

Cross joints, where one tray ends and the next begins, are the part that needs the most care. They are formed with welts or end laps, and at the ridge, the eaves, the verges and every penetration there are trims and flashings in the same metal. The detailing at these points, more than the seams, decides how watertight the finished roof is.

Which metals suit the system

Standing seam is a form of construction, not a single material. It is made in coated steel, aluminium, zinc and copper, and each one weathers in its own way. Steel and aluminium arrive with a factory coating, while zinc and copper are left to form their own surface layer, so the coating, or the lack of one, shapes how the roof ages over time.

Zinc is the one with a published lifespan. VMZinc, the maker, puts it this way: "When correctly designed and installed a zinc roof can last in excess of 100 years." The wording is the maker's own. It describes a roof detailed and fitted properly, and it does not promise that any particular roof will reach that age.

Metals used for standing seam
MetalSurfaceAgeing
Coated steelFactory coatingCoating wears, edges may rust
AluminiumFactory coatingCoating fades over time
ZincNatural patinaSurface darkens to a patina

The structure beneath matters too. A standing seam roof is light and needs a continuous deck, or a purlin layout designed for it, so it is specified with the building rather than laid over whatever happens to be there.

Where a seam roof can fail

Because the fixings are hidden, the faults are in the details rather than on the open surface. A seam that was not folded fully can open under wind and let water in. A clip that was set wrongly can stop the tray moving freely, so the metal buckles or the seam tears. Dents from a ladder or a dropped tool can break a coating and start corrosion, a process the cut-edge corrosion page describes for coated steel.

A survey reads the seams along their length, the cross joints, the trims and flashings, the gutters at the eaves and any rooflights set into the trays. Because the fixings cannot be seen, a fault is traced by the pattern of the damage rather than a loose screw. Walking on the roof can also harm it, which is why the work is done from boards or a platform.

Whether to repair a section or replace the covering is set out on the repair or replace page, and the commercial roofing hub lists the other coverings a commercial building can carry. A figure for any of this has to wait for a reading of the roof itself.

Standing seam roofs, questions answered

01Why does a standing seam roof have no visible screws?

The clips that hold the trays are screwed to the deck underneath the seams and then locked into them as the seams are folded. Nothing passes through the weather-facing metal. That removes the screw heads and washers that can weather on a through-fixed sheet, though the clips and seams still need to be sound, which is what a survey reads.

02How long does a zinc standing seam roof last?

The only lifespan on offer comes from VMZinc, the maker, which states that a zinc roof can last in excess of 100 years when it is correctly designed and installed. That is a manufacturer's statement about a well-detailed roof, so it is quoted as theirs and not as a promise for any given building. Workmanship, drainage and the structure beneath all play a part in how long a real roof lasts.

03Can a standing seam roof be walked on?

It should be walked on as little as possible. Footsteps can dent the metal, crush a seam or break a coating, and a dent can become the start of corrosion. Work on the roof is done from boards laid across several seams to share the weight, and the seams are never used as handholds. Check the deck below for fragility too.

04Is it the same as a composite insulated panel roof?

No. A standing seam roof is a single metal layer in trays with hidden clips, and the insulation sits below it as a separate part of the build-up. A composite panel carries its insulation inside the panel. Both are metal, and they can look alike from the ground, so the single-ply membrane page is worth a look as a third option.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote