Call 01582 935272

Flat roofing

What is a single-ply roof membrane?

Single-ply is a family of flat roof coverings made as manufactured sheets. The name is about how the layer is built, so it covers some materials and leaves others out.

Get a written quote

Call 01582 935272WhatsApp us

A loft with spray foam removed
PicturedA loft with spray foam removed.

The short answer

A single-ply roof membrane is a flat roof covering made as one factory-made sheet, laid in a single layer over the deck. EPDM, TPO and PVC are three single-ply materials. Two coverings that can look similar fall outside the term: GRP is laminated wet on site, and felt is built from several bitumen layers.

A roof drawing with its parts named: lantern, rubber deck, outlet, lead flashingLanternRubber deckOutletLead flashing

What single-ply means on a flat roof

The name is literal. Single-ply means a roof waterproofed by one layer of manufactured sheet, supplied on a roll and cut to the shape of the roof. Because the sheet is made in a factory, its thickness is set in production rather than by how a roofer mixes or lays it. Everything above the deck and any insulation is that one sheet. Fewer layers can mean fewer places for the build-up to go wrong, but the quality of the joins and edges still decides how the roof performs.

The sheets are made of synthetic materials. EPDM is a synthetic rubber. A TPO membrane is made from thermoplastic polyolefin and a PVC membrane from polyvinyl chloride, and sheets in those two plastics can be heat-welded at the joins, while rubber sheet is bonded with adhesive. Whatever the material, the joins between sheets and the turn-up at walls and kerbs are the places where the roof is most carefully detailed.

Single-ply is one approach within flat roofing, and it exists beside two older traditions, laminated fibreglass and layered bitumen felt. The label on its own does not say which material is under the surface, so a quote should name the covering as well as the system. That one sentence in a quote settles a good deal of confusion later.

Which coverings count as single-ply

It is easy to put every modern flat roof into one box. The test is simple: is the waterproof layer a single sheet that arrives ready-made? If it is, the roof is single-ply, and if it is mixed or built up on site, it is not. A roof with two sheets laid one over the other is a different case again, and a survey looks at which is actually there.

Mistakes here matter when quotes are compared. A price for a rubber sheet and a price for a wet laminate are not the same product, and each comes with its own detailing, its own care and its own recorded lifespans. Asking for the covering by name, and for the thickness and make where the supplier states them, puts the quotes on an equal footing.

Flat coverings sorted by how they are built
CoveringSingle-ply?How it is made
EPDM membraneYesRubber sheet
TPO membraneYesPlastic sheet
PVC membraneYesPlastic sheet
GRPNoResin and fibreglass, wet
Built-up feltNoBitumen layers

The EPDM, GRP and felt guide compares the three most discussed options, and the EPDM roof answer looks at the rubber sheet in detail.

Falls, cost and fixing on a single-ply roof

A sheet lying flat can hold water, so drainage has to be designed in. BS 6229:2025, which BSI lists as current, covers flat roofs with continuously supported flexible waterproof coverings, and single-ply sits squarely in that scope. NFRC reports that it sets a minimum 1:80 finished fall for general roof areas and internal gutters. IKO, a membrane maker, says the code asks for a roof to be designed for a fall of 1:40 so that 1:80 is achieved. The minimum fall answer goes through both numbers.

On price, Which? Trusted Traders priced a rubber EPDM or PVC flat roof, new boards included, at £1,950 to £4,000 for a 6m x 3m garage in November 2025, excluding VAT. A house extension would sit in a different range. MyJobQuote puts the average cost of a flat roof replacement at £1,500 to £6,000 in 2026, on a page dated 20 October 2026.

Sheets can be held down by bonding them, by fixing them mechanically through the deck or by weighting them with ballast, and the choice depends on the roof and its construction. A survey settles it, since the deck, the edges and the insulation underneath all affect how a given sheet is fitted.

Single-ply questions, answered plainly

01Is EPDM a single-ply roof?

Yes. EPDM, a synthetic rubber, comes as a manufactured sheet laid in one layer, so it falls inside the single-ply family. HomeBuilding gives it 25-30 years, and Less says EPDM rubber membrane typically lasts 30 to 50 years. The two figures are quoted as published, with no explanation of the gap, and each is an estimate, not a forecast for your roof.

02Are GRP and felt single-ply roofs?

No. GRP is a wet laminate of fibreglass and resin that cures on the roof, and built-up felt is a set of bitumen layers laid one over another. Neither arrives as one manufactured sheet. Listing them as single-ply is a known error, and a quote that does so deserves a question about what is actually being supplied. Ask for the covering by name.

03What does a single-ply roof cost?

Which? Trusted Traders give £1,950 to £4,000 for a 6m x 3m garage roof covered in rubber EPDM or PVC, new boards included, excluding VAT, as of November 2025. A house roof is larger and sits in another range. The figure that matters for you is a single written price from us after the survey. How easily the roof can be reached and the condition of the deck move a price too.

04How are the joins in a single-ply roof made?

Sheets overlap at their edges, and the overlap is closed by heat welding or by adhesive, depending on the material and the system. The join is a detail to ask about, along with how the sheet is formed at corners and upstands. Both points come up when a survey looks at how the roof is built and where it is likely to wear.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote