Call 01582 935272

Lead roofing

What is code 5 lead?

Code 5 is the third of the six thickness codes for rolled lead sheet. At 2.24 mm it is thicker than code 4, and the makers print a weight per square metre for it.

Get a written quote

Call 01582 935272WhatsApp us

Lead roll roof on a bay window of a Victorian villa
PicturedLead roll roof on a bay window of a Victorian villa.

The short answer

Code 5 lead is rolled lead sheet 2.24 mm thick, made to BS EN 12588. Both Calder's and Ecobat's weight charts list it at 25.40 kg per square metre. It sits between code 4 at 1.80 mm and code 6 at 2.65 mm, and the specification for each job names the code for each detail.

A roof drawing with its parts named: lead valley, tiles, hipLead valleyTilesHip

The figures behind code 5

Code 5 is one step up from code 4 in the set of thickness classes defined in BS EN 12588, which runs from code 3 to code 8. The standard sets the thickness for each code, and code 5 is 2.24 mm. Each maker then publishes the mass of a square metre of sheet at that thickness.

  • Thickness: 2.24 mm.
  • Calder's weight chart: 25.40 kg per square metre.
  • Ecobat's weight chart: 25.40 kg per square metre.

The two makers print the same weight for this code, so a figure quoted for code 5 does not depend on which of the two charts it came from. The comparison does not extend to every code, because codes 3 and 6 differ between them, and a weight from any other maker should be read off that maker's own chart.

A weight per square metre belongs to the sheet, not to a roof, and it is not the same as a total for the job. The lead on a particular job weighs whatever its total area comes to at that rate. Working that out needs the drawn areas from the specification and a survey, and the lead roofing hub explains the details those areas are made up of.

Code 5 in the full range of codes

Set against the codes above it, code 5 is the lightest of the four in the table. The table gives the four codes from 5 to 8 with both makers' weights.

Thickness and weight for codes 5 to 8
CodeThicknessCalderEcobat
52.24 mm25.40 kg/m225.40 kg/m2
62.65 mm30.05 kg/m230.10 kg/m2
73.15 mm35.72 kg/m235.72 kg/m2
83.55 mm40.26 kg/m240.26 kg/m2

Each step up the table adds between 0.40 and 0.50 mm of thickness, so the thicknesses climb in fairly even stages while the weights climb by roughly five kilograms per square metre. Code 5 is 0.44 mm thicker than the code below it, which is covered in what is code 4 lead, and 0.41 mm thinner than code 6. Of the four codes in the table, only code 6 gets a different weight from each maker, 30.05 from Calder against 30.10 from Ecobat.

The table is a reference for sizes only, and it is not a guide to which detail takes which code. The lead sheet codes guide takes the whole range in order.

Reading a quote that names code 5

A written quote or specification that names code 5 is naming a thickness, 2.24 mm. It is worth checking that the code and the detail it is attached to are both written down, since the specification sets the code for each part of the roof separately. A quote that names code 5 for one flashing says nothing about the code on the next.

Thickness is not the only thing a quote should make clear, but it is the one that can be checked later, because lead is a metal with a measurable gauge. If the lead on the roof has been in place for some time, an exposed edge can be measured with callipers during a survey, which gives a check against any paperwork that survives. Where the paperwork and the measurement disagree, the measurement is the fact to work from.

On durability, MyJobQuote says that when correctly installed, lead flashing can last for over 80 years (over 100 years for higher codes) with minimal maintenance. It does not say which codes count as higher, so no lifespan for code 5 follows from it. Whether lead is patched or renewed follows from its state, and the page on repair or replace lead flashing goes through that decision.

Questions about code 5 lead

01How much thicker is code 5 than code 4?

By 0.44 mm: code 4 is 1.80 mm and code 5 is 2.24 mm. In weight, Calder's chart shows an increase from 20.41 to 25.40 kg per square metre, a difference of 4.99. Ecobat's chart gives the same two figures. The difference is a matter of measurement, and what it means for a detail is for the specification to decide.

02Do Calder and Ecobat agree on the weight of code 5?

Yes. Both charts give 25.40 kg per square metre for code 5, under the heading of rolled lead sheet to BS EN 12588. The two charts disagree on codes 3 and 6 only. When lead from a different maker is specified, ask for that maker's chart, so that the weight you are quoted matches the sheet that arrives on site and the figures in the specification stay consistent.

03May a roof carry both code 4 and code 5?

Yes, since the specification names a code for each detail, not one code for the whole roof. Different thicknesses can sit in different places. A written quote that lists the codes beside the details they apply to lets you see which thickness goes where, and that same list helps if a later repair has to be matched to what was laid originally.

04Does thicker lead always last longer?

MyJobQuote says correctly installed lead flashing can last for over 80 years, and over 100 years for higher codes. That wording is about flashing, and it does not name the codes it means. How long any piece of leadwork lasts also turns on how well it was fitted, what it sits on and how much the roof moves, not on thickness alone, so a code is only one input to the question.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote