Call 01582 935272

Lead roofing

How heavy is lead sheet per square metre?

Lead sheet is weighed per square metre, and the figure depends on the code. Calder and Ecobat each publish a chart, and the two agree on four of the six codes.

Get a written quote

Call 01582 935272WhatsApp us

A freshly repointed brick chimney with new lead flashing and flaunching on a clay tile roof
PicturedA freshly repointed brick chimney with new lead flashing and flaunching on a clay tile roof.

The short answer

On Calder's chart, rolled lead sheet weighs between 14.97 and 40.26 kg per square metre, by code. Code 4, at 1.80 mm thick, is 20.41 kg on both Calder's and Ecobat's charts. The two makers differ at codes 3 and 6, so a weight is only given alongside the name of the maker.

A roof drawing with its parts named: lead valley, tiles, hipLead valleyTilesHip

The weight chart for codes 3 to 8

Sheet lead for roofs is made to BS EN 12588 in codes 3 to 8, and each code is a thickness. Each maker then prints the mass of a one-metre square of sheet cut at that thickness, in kilograms. Both makers head their charts as rolled lead sheet to the standard. The table sets out the thickness and both makers' figures, as printed on Calder's and Ecobat's weight charts.

Lead sheet weight per square metre, codes 3 to 8
CodeThicknessCalderEcobat
31.32 mm14.97 kg15.0 kg
41.80 mm20.41 kg20.41 kg
52.24 mm25.40 kg25.40 kg
62.65 mm30.05 kg30.10 kg
73.15 mm35.72 kg35.72 kg
83.55 mm40.26 kg40.26 kg

Every figure is for one square metre, so it describes the sheet and not a finished roof, and the amount of lead on a roof depends on its area. The weight rises in step with the thickness: on Calder's chart, code 8 is about 2.7 times the weight of code 3, and 3.55 mm is about 2.7 times 1.32 mm. The lead roofing hub explains where the different thicknesses are put to use.

Where Calder and Ecobat differ

Four of the six codes carry the same weight on both charts, and two do not. The differences are small, but they are the reason a weight is never quoted without the name of its maker.

  • Code 3: Calder gives 14.97 kg, Ecobat gives 15.0 kg.
  • Code 6: Calder gives 30.05 kg, Ecobat gives 30.10 kg.

For codes 4, 5, 7 and 8 the two charts match to the hundredth of a kilogram. When reading any chart, check three things: the standard in its heading, the maker's name and the unit, which is kilograms per square metre. A weight from a third maker is not covered by either chart, and it should be read from that maker's own chart. If a quote or a specification gives a weight, ask which maker's chart it was taken from, since a figure with no maker named cannot be checked.

Thickness is the steadier figure to work from, because the standard fixes it for each code and no maker varies it. The guide to lead sheet codes explained covers the thickness side in more detail.

Turning a weight per square metre into a piece

A figure per square metre becomes the weight of a piece by multiplying it by the piece's area. A strip of code 5 lead covering half a square metre weighs half of 25.40 kg on either chart, which is 12.70 kg. A piece of code 4 of 2 square metres weighs 40.82 kg on Calder's chart, or on Ecobat's.

The arithmetic is for sheet weight only, and the figure it gives is the mass of lead sheet, which is a separate matter from the load a roof structure carries. It gives what a piece of lead weighs; it cannot give what a job will cost, how many pieces a roof needs or which code belongs on which detail. The specification decides the last of these, and the page on what is code 4 lead works through one code in full.

Weight on the chart is not a measure of how long the lead will last. MyJobQuote says that correctly installed lead flashing can last for over 80 years, and over 100 years for higher codes. The statement is about flashing and leaves out which codes it counts as higher, so a weight chart cannot be read as a lifespan table. A quote with both the code and the maker written on it lets the sheet that arrives be checked against the chart.

Lead weights, your questions

01Do the two makers list different weights for code 6?

Yes, by a small amount. Calder's chart gives 30.05 kg per square metre and Ecobat's gives 30.10 kg, a difference of 0.05 kg. Code 3 differs as well, at 14.97 kg against 15.0 kg. The other four codes are identical on the two charts, so only those two rows of the table depend on which maker is named, and a figure for either should carry the maker's name.

02How is the weight of one piece of lead worked out?

Multiply the weight per square metre for the code by the area of the piece in square metres. A piece of code 6 of 1.5 square metres on Calder's chart is 45.075 kg, since 30.05 times 1.5 comes to that figure. Use the same maker's chart for the code throughout, because the other maker's figure for code 6 is slightly different.

03Does the weight rise in proportion to thickness?

It does, to the precision of the charts. Code 8 is 3.55 mm against 1.32 mm for code 3, a ratio of about 2.7, and Calder's weights for the same two codes, 40.26 and 14.97 kg, give the same ratio. Each code adds roughly 0.4 to 0.5 mm of thickness, with the weight climbing alongside it, so a code's thickness tells you its weight up to the small differences between makers.

04Is the heavier code the longer-lasting lead?

Weight measures what the sheet is, not how it lasts. MyJobQuote says correctly installed lead flashing can last for over 80 years, with over 100 years for higher codes, and it names no particular code. Fitting, the deck beneath and the movement of the roof all bear on how long a piece of lead lasts, and a survey looks at them.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote