Call 01582 935272

Cleaning methods compared

Roof cleaning methods compared: scraping, soft wash, pressure and steam

Hand scraping, soft wash, high-pressure jets and steam all get moss and algae off a roof, and they do it in different ways with different risks. Each is described below, then set against the covering it suits.

9 minute read

Get a written quote

Call 01582 935272WhatsApp us

A gutter full of leaves, moss and a broken tile after a storm
PicturedA gutter full of leaves, moss and a broken tile after a storm.
A roof drawing with its parts named: moss, lichen, washed tiles, gutterMossLichenWashed tilesGutter

Four methods, one comparison

Firms that clean roofs can specialise in one method and describe it as the safe one. That is natural, since a business sells what it does. The result for an owner is a set of competing claims, each from someone with a reason to make it, and no easy way to weigh them.

No single method is right for every roof. Each works in its own way, carries its own risk to the covering and asks something different of the person using it, from the tool in hand to the product in the tank. A firm that offers only one of them may still be the right choice for a roof that suits that method.

Four roof cleaning methods in brief
MethodHow it worksMain risk
Hand scrapingTools lift growth by handScored or chipped surfaces
Soft washLow-pressure water and a solutionRun-off and product choice
High-pressure jetA jet of water under high pressureSurface loss, joint damage
SteamHot water or steam at the surfaceHeat and moisture on the covering

Two ideas run through all four. First, every method can take something from the surface, even if only a thin layer, so the question is how much. Second, the covering matters. A method that suits a sound concrete tile may not suit a worn clay one, a slate or a felt flat roof, and the survey decides which applies. Age is the third thread, because a tile near the end of its life gives up its surface sooner under any of the four.

Hand scraping and brushing

Hand scraping uses a plastic or metal scraper, a stiff brush or a similar tool to lift moss and lichen off the surface by hand. Done slowly, it is the method that gives the person doing it the most feel for what they are removing. They can see a tile move, a crack open or a layer come away, and stop.

It is also the slowest method, and the labour is the cost. A whole roof is hours of work at height. The method suits smaller roofs, patches of growth and roofs that cannot take water or chemicals, and it is a sensible first step before a rinse on a heavily grown slope.

Its risk lies in the tool. A hard scraper dragged across a tile scores the surface, and a metal blade can chip an edge or cut a membrane. Scraping against the lie of a tile can lift the edge of the one above. A careful hand with the right tool leaves little trace, while a hurried one can leave a roof marked.

Hand work does not treat what is left behind. Spores and root-like threads remain in the surface, and growth can return. A hand-lifting approach is described in the blog post on moss on roof tiles, and a biocide can follow it where the label suits the covering.

Soft wash and what "soft" means

Soft wash applies a cleaning solution at low water pressure, sometimes through a pump and a long hose, and lets the solution do the work. The growth is loosened and killed by the chemistry, and a gentle rinse can follow. It is quicker than hand scraping over a large area, and it does not blast the surface.

The word "soft" is a description, not a measurement. There is no single pressure at which a wash becomes soft, and the name says little about the product in the mixing tank. A quote that says "soft wash" should go on to name the product, its strength and the rinse, since those are the parts that decide what happens to the tile and to everything the run-off touches.

The risks are the chemicals' risks. Overspray and run-off can mark paint, lead and plastic, harm plants and reach water butts and ponds, and a strong mix can dull a surface. The product label sets out what it can harm and how to use it, and the guide to biocide roof treatments covers the questions to put.

Soft wash suits a sound roof, but it does not suit every roof. A roof with failed bedding, loose tiles or an unsealed ridge can let liquid into the roof space, and a flat roof membrane needs a product made for it. Where the covering is sound, it is a gentle route; where it is not, the first job is a repair.

High-pressure jets and the maker's warning

A high-pressure jet forces water through a nozzle. It strips growth quickly, and the result is dramatic: a roof can go from green to bare in a morning. The cost is that the same force acts on whatever lies beneath the moss.

Marley, a maker of tiles and slates, says: "The use of high powered jet washes is not recommended as it can damage the surface of the slate or tile, thus reducing its expected life considerably". That warning comes from a maker, and it names slate and tile alike.

Beyond the surface, a jet is aimed up a slope, into the joints between courses and along ridges and verges, which are places where bedding is exposed. Pressure can loosen mortar, lift a tile edge and chip a face. A roof that has been jetted can look clean and be rougher than before, which means it holds moss and water better.

Pressure is not one setting. A garden-style washer, a trade machine and a rotary tool are different things, and the gentler end of the range is closer to a rinse. If pressure is part of a quote, ask for the pressure, the nozzle and the distance in writing, and set them against what the tile maker says.

Steam and hot water

Steam and hot-water cleaning use heat to loosen and kill growth, sometimes with little or no chemical. The method is described by those who offer it as gentle, and it avoids the run-off questions that a biocide raises. Heat is the working agent, and moisture is the by-product.

The risks are different. Heat and moisture reach the surface together, and the tile maker's guidance on steam is the place to look, rather than the sales line. A glazed, painted or coated tile may react to heat in ways an unfinished one does not. Heat also reaches the edges of lead, plastic and felt, which have their own limits.

Steam is slower than a jet and uses specialist equipment, so it can carry a different cost. It is not a treatment either. It kills and loosens growth that is there, and what keeps a roof damp afterwards is not changed. Regrowth depends on the conditions, as with every other method.

As with soft wash, a sound covering is the starting point. Steam on a roof with failed bedding or a leaking ridge can drive moisture to places it should not go. A roofer who has looked at the roof first can say whether the covering is in a state to take it, and the damage risks are set out in can roof cleaning damage tiles.

How the covering changes the answer

The same method behaves differently on different materials. The table sets out the main coverings against the methods, and the age and condition of the individual roof can move any entry.

Methods against coverings: general cautions
CoveringGentler optionsTake most care with
Concrete tileHand lifting, soft washHigh pressure
Clay tileHand lifting, soft washHigh pressure, heat on glaze
Natural slateSoft brush, low rinseHard jets, hooks and nails
Felt, EPDM, GRPBrush, low rinseScrapers, jets, solvents

Slate is covered in its own guide, how to clean a slate roof, and flat roof coverings have their own cautions. Tile roofs bring two points worth pressing on in any quote: the surface wear on concrete and the bedding on clay. Ask whether the method in a quote changes with the covering, and what it does differently on each where a house has more than one roof material.

A roof can also need two methods. A hand pass to lift a thick mat, followed by a soft rinse, is a different job from either one alone. Firms can combine methods, and a quote that says which is used for which part of the roof is more useful than one that names a single technique for the whole thing.

Questions that expose the method

Method can be hard for an owner to judge, because it happens out of sight, on the roof, while nobody is watching. The way round that is to ask for it in writing, and to ask in terms that cannot be answered with a brand slogan.

  1. Which method is used on my roof, and why that one?
  2. If water is used, at what pressure, through which nozzle and from how far?
  3. If a product is used, what is it, and may I read its label?
  4. How will the roof be walked on, and with what protection?
  5. What happens to tiles found loose, and to the gutters?

Specific answers show that the roof has been looked at. Vague ones suggest a method was chosen before the roof was seen. The cost side is set out in roof cleaning prices, and a survey comes before the single written total. Write the answers down, since a method that changes between the quote and the day is a change that should be agreed again.

To begin with a photo, send one of the roof on WhatsApp for a first look. The rest of the cleaning guides sit under roof cleaning, and the right method follows from what the survey finds.

Cleaning method questions, answered

01What is the gentlest way to clean a roof?

Hand lifting and brushing put the least load on a sound roof, followed by a low-pressure rinse. Each takes longer and costs more in labour. Which one is gentlest for your own roof turns on the tiles, their age and the bedding, so ask for the planned method in writing before work starts, along with how the roof is to be walked.

02Is soft washing safer than pressure washing?

It avoids the force of a jet, which is the main risk to a tile surface, but it brings chemical run-off and product questions of its own. Neither is safe by name. The pressure, the product and the roof's condition decide the result, so ask for the product label and the pressure to be stated before anyone starts, and for the downpipes to be dealt with.

03Does steam cleaning damage roof tiles?

It can if the tile cannot take the heat, as with some glazed, painted or coated faces, or if moisture is driven into a roof with failed bedding. Steam is slower than a jet and avoids some chemical questions. Check the tile maker's guidance on steam for your tiles, and ask who has looked at the bedding and ridge first.

04Why do cleaners disagree about which method is right?

Each firm can work with one method and describe it as the safe one. Suitability depends on the roof, so compare answers about the covering, the pressure and the product rather than slogans. Weigh each method against your own covering, how old it is and how sound the ridge and verge bedding are, and ask each firm how its method would treat that roof. No method is risk-free, and the covering, not the sales line, decides which risk applies to your house.

05Can two methods be used on one roof?

Yes. A hand pass to lift a thick mat followed by a low-pressure rinse is one sequence that can suit a heavy build-up, and a biocide can follow where the label suits the covering. A quote should say which method is used on which slope, and why, instead of naming a single technique for the whole roof, so that you know what each part of the roof is getting.

Get a written price for your roof

10-year workmanship guarantee, in writing

Tell us about your roof

Call WhatsApp Written quote